02.1 Oxide vs bisglycinate

Magnesium oxide vs bisglycinate: what the blend hides

Technical document 02.1 · Reviewed 2026-11-18 · Magnesium Bisglycinate

On this page
  1. Two numbers, two materials
  2. Why blends exist
  3. How a blend is detected
  4. What the label can say
  5. What to write into the specification
  6. Questions to put to a supplier

Magnesium oxide carries about 60% elemental magnesium; magnesium bisglycinate carries about 14%. A blend of the two can hit almost any figure in between, including the 20% figure some suppliers quote as “magnesium glycinate”. The magnesium assay cannot tell the two sources apart, which is why a form claim needs a test that looks at the ligand as well as the metal.

In one line

Magnesium oxide carries about 60% magnesium; the bisglycinate carries about 14%. A blend can hit any number in between and still be called magnesium glycinate.

Two numbers, two materials

Magnesium oxide, MgO, is 60.3% magnesium by mass. Magnesium bisglycinate, Mg(C₂H₄NO₂)₂, is 13.9% magnesium. The difference is not a matter of grade or purity; it is the difference between an inorganic oxide and an organic chelate.

This has a practical consequence for reading a quotation. An anhydrous bisglycinate cannot exceed about 14.1% magnesium. A certificate that reports 18%, 20% or 22% magnesium is therefore describing something else: a blend with oxide or carbonate, a different salt, or a material with a carrier that has been counted in the assay. None of those is automatically unsafe, but none of them is the chelate the label may imply.

Why blends exist

Blending is a commercial answer to three pressures. Magnesium oxide is inexpensive per kilogram of magnesium, so a blend lowers the cost of a “magnesium glycinate” position. Oxide also raises the elemental magnesium figure, which looks better on a short specification. And oxide is a fine, dense powder that can improve flow in a blend that would otherwise be light and cohesive.

The result can be a legitimate product. A formulator who wants a high-magnesium, low-cost powder may choose a blend deliberately. The problem is not the blend; the problem is calling it the chelate when the buyer is paying for the chelate and the label names only the chelate.

How a blend is detected

The first check is arithmetic. If the magnesium figure is above the theoretical maximum of the anhydrous chelate, the material contains another magnesium source. The second check is the ligand. The chelate has a fixed Mg : glycine molar ratio of 1:2; if the glycine figure is low relative to the magnesium, part of the magnesium is not chelated.

The third check is crystallography. X-ray diffraction detects crystalline magnesium oxide in the powder. The detection limit depends on the method and the laboratory, so the report should state it. The fourth check is FTIR, which shows the coordination of the glycine to the magnesium; a physical mixture of oxide and chelate does not produce the same spectrum as a reacted chelate.

A solubility or acid-digestion check can support the picture but does not replace the spectroscopic evidence. Magnesium oxide is sparingly soluble in water; a cloudy dispersion is a hint, not a proof. The proof is the combination of the elemental assay, the ligand assay and a method that sees the crystal form.

What the label can say

In the European Union, the ingredient list has to name the magnesium source as listed in Annex II of Directive 2002/46/EC. Magnesium bisglycinate and magnesium oxide are separate entries. A blend has to declare both, in descending order by weight. A label that names only magnesium bisglycinate while the drum contains oxide is a labelling problem before it is a quality problem.

In the United States, the Supplement Facts panel declares elemental magnesium, and the ingredient list names the source. A blend should name both sources. The elemental figure alone does not tell the consumer or the retailer which form was used.

The same logic applies to the specification. If the purchase order says “magnesium bisglycinate”, the certificate should prove the chelate. If the purchase order says “magnesium blend”, the certificate should name the components and their proportions. A purchase order that says only “magnesium 20%” has not specified a material.

What to write into the specification

  • “Magnesium bisglycinate, 1:2 chelate; no added magnesium oxide.”
  • “Magnesium 13.5–14.2%; glycine 84.0–88.0%; Mg : glycine 1.95–2.05.”
  • “Free glycine ≤1.0%.”
  • “XRD: no crystalline magnesium oxide detected, detection limit reported.”
  • “If blended, declare each magnesium source and its contribution.”

The specification should also say who is responsible for the blend declaration. If the material is blended after the chelate is manufactured, the blender is the manufacturer of the blend and the certificate should come from the blender, not from the chelate producer.

Questions to put to a supplier

  • Is the material a single chelate or a blend? If a blend, what are the components and ratios?
  • What is the magnesium figure, and what is the glycine figure on the same lot?
  • Is there an XRD or FTIR report for this lot?
  • Which magnesium source was used in the reaction?
  • Does the certificate name the hydrate state?

A supplier who can answer these five questions is selling a specification. A supplier who answers only the first one with a percentage is selling a number. The identity page explains the test sequence; the grade page explains where the blend sits in the range; the compliance page covers the labelling rules.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation