14%, 11%, buffered or granulated: choosing a magnesium bisglycinate grade
Magnesium bisglycinate is sold in several grades that share a name but not a composition: the anhydrous chelate at about 14% elemental magnesium, the monohydrate and dihydrate at lower figures, buffered blends that add magnesium oxide, and milled or granulated versions of the same chemistry. The grade is chosen by the dosage form and the label claim, not by the highest number on the first quotation.
The grade is decided by the dosage form and the label, not by the magnesium percentage on the first quote.
Why the grade is not the assay
Two powders can both be called magnesium glycinate and still differ in three ways that matter to a formulator: the hydrate state, the amount of unreacted magnesium oxide, and the particle size. The elemental magnesium figure is the sum of those differences, but it does not explain them.
This is why a quotation that leads with a percentage is incomplete. The useful question is not “how much magnesium” but “which molecule, in which hydrate, with what else in the drum”. The answer decides the label, the fill weight, the flow on the tablet press and the taste of the finished product.
The grades side by side
| Grade | Elemental Mg | Form | Fits | Watch |
|---|---|---|---|---|
| Anhydrous chelate | about 14.1% | Mg(C₂H₄NO₂)₂ | Capsules, tablets, powder blends | Hygroscopic; confirm LOD and packing |
| Monohydrate | about 12.6% | Chelate with one water | General powder blends | More mass per mg of magnesium |
| Dihydrate | about 11.8% | Chelate with two waters | Blends where flow matters | Hydrate state must be on the label |
| Buffered blend | varies, often above 14% | Chelate plus magnesium oxide or carbonate | Cost-driven projects | Not the same label ingredient |
| Granulated | same as base grade | Agglomerated powder | Tablets, sachets | Confirm granulation aids |
| Milled, 80 mesh | same as base grade | Finer powder | Capsules, suspensions | Dust, flow, blend segregation |
What changes in the drum
The anhydrous chelate carries the most magnesium per kilogram, which is why it is the reference grade for capsule and tablet formulas with a tight fill weight. The hydrates carry less magnesium per kilogram and more water, so a formula that was built on 14% needs a new fill weight if the grade changes. The change is arithmetic, not a quality difference, but it has to be made deliberately.
A blend that adds magnesium oxide raises the elemental magnesium above what the pure chelate can carry. The anhydrous chelate cannot exceed about 14.1% magnesium by mass; a figure of 18% or 20% is therefore a signal to ask what else is in the drum. That is not automatically a bad material, but it is a different material, and the label has to say so.
Granulation changes flow and dust, not the chemistry. Milling changes particle size and dissolution rate, not the assay. Both are legitimate ways to fit a dosage form, provided the specification names the process and the excipients used.
What changes in the finished product
For capsules, the constraint is fill weight. A 100 mg elemental magnesium dose needs about 710 mg of a 14% chelate, before any excipient. The same dose needs about 790 mg of the monohydrate and about 850 mg of the dihydrate. In a 500 mg capsule, the grade decision is also a capsule-count decision.
For tablets, bulk density and flow decide whether the blend runs on the press. A fine milled powder may need granulation; a granulated grade may need a different lubricant. For stick packs and drink mixes, dissolution rate and taste matter more than the last decimal of the assay. For gummies and chews, the pH and water activity of the matrix can change how the chelate behaves, and the taste of the magnesium salt becomes part of the product.
None of these decisions is settled by the certificate alone. They are settled by a bench trial with the grade that will actually ship.
When not to upgrade
If the label claim is elemental magnesium, the formula has room for the extra mass, and the certificate documents the form, a hydrate grade can be the correct choice. Paying for a more concentrated grade only makes sense when the fill weight, the capsule size or the freight cost makes the concentration worth something.
Likewise, a granulated grade is not an upgrade for a capsule formula that already flows well, and a finer mesh is not an upgrade for a tablet blend that needs density. The grade should solve a problem the dosage form actually has.
What to put in the specification
- “Magnesium bisglycinate, anhydrous, 13.5–14.2% Mg by complexometric titration.”
- “Glycine 84.0–88.0% by HPLC; Mg : glycine ratio 1.95–2.05.”
- “Free glycine ≤1.0%; loss on drying ≤2.0%.”
- “Particle size ≥95% through 40 mesh; bulk density 0.55–0.90 g/mL.”
- “No added magnesium oxide; XRD screen reported on request.”
The grade table above is only useful if the certificate repeats the same definitions. A specification that names the form, the hydrate and the particle size gives the laboratory something to test against; a specification that names only the magnesium range does not.
For the tests behind these figures, read the COA page. For the difference between a chelate and a buffered blend, read oxide versus bisglycinate. The regulatory status of the form is on the compliance page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation