06 Identity & adulteration

How we prove a lithium orotate lot is the anhydrous salt

Technical document 06 · Reviewed 2026-11-19 · Lithium Orotate

On this page
  1. Five layers of identity
  2. The 1:1 ratio: orotate 95.7%, lithium 4.28%
  3. X-ray diffraction: one crystal or two?
  4. What substitution looks like
  5. Writing identity into the specification
  6. Five questions for the supplier

A lithium orotate lot is that salt when five lines agree: the document names the anhydrous salt and its CAS number, IR and HPLC match the reference, the lithium figure sits inside 4.0–4.5%, the loss on drying stays under 1.0%, and the numbers close as a mass balance. The assay alone cannot separate the salt from a blend, because a blend can be built to land inside the assay window. The lithium figure is the direct check on the counter-ion.

In one line

The lithium figure proves the counter-ion, IR and HPLC prove the orotate, and the mass balance shows whether both were measured on the same powder.

Five layers of identity

Naming the right material on paper is not the same as proving it in the drum. Each layer below answers a different question, and a supplier who answers only the first has shown you a document, not a powder.

Five layers of lithium orotate identity
LayerQuestion it answersEvidenceWhat it settles
DocumentIs the form named?Name, CAS 5266-20-6, formulaOnly the paperwork
InfraredWhich anion is it?IR against a reference spectrumThe anion family
ChromatographyIs the anion the right one?HPLC retention against a standardThe anion, not the cation
Counter-ionIs the cation lithium?Titration, or ICP-OES as a cross-checkThe salt
Mass balanceIs it diluted?Assay, lithium, loss on dryingConsistency of the numbers

The 1:1 ratio: orotate 95.7%, lithium 4.28%

Orotic acid is a pyrimidine carboxylic acid with one acidic proton, so the salt pairs one orotate anion with one lithium cation. The molar mass is about 162.03 g/mol, of which 6.94 g is lithium and 155.09 g is the orotate part: 4.28% lithium against 95.7% orotate, a mass ratio of about 1 to 22. That ratio is fixed by the formula and does not move with the assay.

It is also the fastest check on a suspicious lot. A powder diluted with orotic acid loses lithium in proportion: a blend with 10% orotic acid reads about 3.9% lithium, outside the window, even though the HPLC assay would still look respectable. A powder extended with lithium carbonate moves the other way, because the carbonate carries 18.8% lithium. Both directions are visible on a single elemental result, which is why the lithium line matters more than its two-decimal appearance suggests.

The window is not infinitely sensitive. A one-percent carbonate addition calculates to about 4.4% lithium and about 99% assay, inside both gates. That is the honest limit of a specification: it catches the crude substitution and leaves the small one to a different test. A slurry pH reading and a drop of acid, which would show gas from a carbonate, cost less than an instrument run and belong in the goods-in screen.

X-ray diffraction: one crystal or two?

Diffraction describes the solid: whether it is crystalline, and whether the lines match a reference. For this salt it is most useful against a physical blend, because a mixture of two crystalline solids shows the lines of both. A single-phase pattern that matches the reference, taken with a lithium figure at 4.28%, is a much stronger statement than either result alone.

It measures neither purity nor the cation. An amorphous lot can be genuine material, and a crystalline pattern can belong to a diluted blend if the diluent is also crystalline. Before a “pattern matches” sentence is accepted, ask for the reference pattern, the scan range and the detection limit. For routine release, IR and HPLC carry identity; diffraction is the escalation when the solid form or a blend is in dispute.

What substitution looks like

Likely lithium orotate substitutions and the signals
AdulterantWhat it doesSignalTest
Orotic acidNo lithium; lowers the elemental figureLithium below 4.0%; assay still plausibleLithium by titration or ICP-OES
Lithium carbonateAdds a lithium-dense, alkaline solidLithium high; gas on acidificationSlurry pH, acid drop, XRD
Another lithium saltWrong anion; different solubilityIR or retention mismatchIR, HPLC, XRD
WaterDilutes the as-received figuresLoss on drying above 1.0%Gravimetric drying
Blend built to passHits assay and lithium windows togetherMass balance that does not closeFull balance plus XRD and pH

Colour is the weakest signal: white to off-white covers a wide range and tells you almost nothing about the counter-ion. The stronger signals are the elemental figure, the IR spectrum, the mass balance and the acid test. Appearance and assay without an identity test leave the likeliest substitution untouched.

Writing identity into the specification

  • “Lithium orotate, anhydrous, CAS 5266-20-6, C5H3LiN2O4.”
  • “Assay 98.0–102.0% by HPLC, with the basis stated on the certificate.”
  • “Lithium 4.0–4.5% by titration, as received; ICP-OES as an independent cross-check on request.”
  • “Identification by IR and HPLC against a reference; chromatogram and spectrum available on request.”
  • “Loss on drying ≤1.0%; heavy metals and microbiology as listed.”
  • “Slurry pH recorded per lot; no carbonate detected by the acid screen.”

Five questions for the supplier

  1. Which form is this lot, and does the certificate name CAS 5266-20-6 and the anhydrous salt?
  2. What is the lithium result, on which basis, and by which method?
  3. Will you send the IR spectrum and the chromatogram as well as the percentage?
  4. What is the loss on drying for this lot, and does the mass balance close against the lithium figure?
  5. If a lot is contested, will you re-test the retained sample jointly, with the referee lab named up front?

Five straight answers make a file. A single assay figure makes a number. The catalog specification is on the product page; each figure is located on the COA page; the salt comparison is on the orotate versus carbonate page; the procedures are collected in the methods library; the release workflow is on the quality page. The sodium molybdate identity page shows the same elemental logic when the metal figure, rather than the anion, carries the proof.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation