02 Grade comparison

Choosing a lithium orotate grade: particle, granulation, dilution

Technical document 02 · Reviewed 2026-11-19 · Lithium Orotate

On this page
  1. Why the grade range is narrow
  2. The three presentations side by side
  3. Flow, dust and a slightly soluble powder
  4. From the claim to the fill weight
  5. What to write into the specification

Lithium orotate is supplied as one salt, so the grade question is narrower than it is for a mineral with several chemical forms. What a buyer can actually vary is the particle: the standard 40 mesh powder, a granulated version on request, and a diluted blend on request. Each changes the flow, the dust, the fill weight and one or two certificate lines, not the identity of the salt. The larger decision — whether to use the orotate at all rather than the carbonate — is a separate question, and it is treated on its own page.

In one line

One salt, three presentations: the mesh, the granulation and any dilution change the flow and the fill weight, not the identity of the salt.

Why the grade range is narrow

The catalog describes a single chemical item: lithium orotate, CAS 5266-20-6, assay 98.0–102.0%, lithium 4.0–4.5%, loss on drying ≤1.0%, at least 95% through 40 mesh. There is no second salt form, no coated grade and no sustained-release version in the range. A purchase order that asks for “a different grade” is therefore usually asking for one of three practical things: a coarser or finer powder, a granulated powder that flows, or a lower assay per gram so the material can be weighed into a small-dose formula.

The lithium window also fixes the hydrate question. One mole of water would add about 18 g/mol and pull the lithium figure to roughly 3.9%, below the catalog floor, so 4.0–4.5% is an anhydrous window by construction. If a supplier offers a hydrated material, it is a different specification item with a different lithium figure, and the pack and the label have to say which one was bought. That is a change of material, not a grade.

The three presentations side by side

Lithium orotate presentations and what each one moves
PresentationWhat changesUsual fitCertificate line to add
Standard powder, 40 meshNothing; this is the catalog gradeCapsules, tablets, dry blends≥95% through 40 mesh
Granulated, on requestFlow, dust, bulk density, wettingHigh-speed tableting, stick packsGranulation method and bulk density
Diluted blend, on requestAssay per gram, carrier, labelVery small doses, premix handlingCarrier identity, assay, mesh, allergen statement

A granulated lot and a milled lot are not interchangeable on a tablet press even when both pass the same assay. The press runs on the flow and the die fill, which are properties of the particle, not of the molecule. A dilution is a bigger change: it puts a second material into the powder, so the ingredient list, the allergen review and the assay arithmetic all move with it.

Flow, dust and a slightly soluble powder

The powder is white to off-white and only slightly soluble in water, so a dispersion in a liquid is a suspension and will settle. Inside a capsule or tablet nothing settles; in a stick pack the sediment is on show unless the powder is milled fine and the formula holds it in suspension. Finer milling helps the suspension and makes the dust worse, which is why the mesh line and the handling instructions belong together.

The catalog does not fix a bulk density. Two lots at the same mesh can fill a capsule die differently, so ask for the lot figure before the fill weight is frozen. Flow is the second physical line worth asking for on a granulated grade: the point of granulation is a repeatable die fill, and a granulation that still bridges in the hopper has not solved the problem it was bought for.

Moisture is the third. The ceiling is 1.0% loss on drying, which is tight for a powder handled in a humid room. The powder is not offered as a moisture-protected grade, and a 1.0% gate leaves little room for pickup after the pouch is opened; a damp powder also flows badly before it fails anything else.

From the claim to the fill weight

One line of the label carries the salt; the panel carries the element. They are two masses, and neither can be filled in from the other. Lithium orotate at 4.28% lithium means a 500 mg capsule carries about 21.4 mg of the element; a 250 mg capsule carries about 10.7 mg, and a 5 mg lithium claim needs about 117 mg of powder. The figure is arithmetic from the formula, not a suggested intake.

Those masses decide the format. At 4.28% the salt is dilute in lithium terms, so a capsule can carry a meaningful quantity of powder without a large elemental dose, which is the opposite of the carbonate at 18.8%. A formulator who writes the elemental target first and then divides by the salt factor will get the fill weight right; one who starts from “500 mg of powder” will write a different label. Either way the certificate, the specification and the label should use the same salt name, the same basis and the same factor.

For a diluted blend the arithmetic changes twice: once for the assay of the blend and once for the carrier. A 10% blend carries about 0.43% lithium, so the fill weight moves by an order of magnitude, and the carrier has to be declared. That is a formulation decision rather than a purchasing convenience, and it should be written into the specification before the first order.

What to write into the specification

  • “Lithium orotate, CAS 5266-20-6, C5H3LiN2O4, anhydrous.”
  • “Assay 98.0–102.0% by HPLC, basis stated on the certificate.”
  • “Lithium 4.0–4.5% by titration, as received.”
  • “Loss on drying ≤1.0%; identity by IR and HPLC.”
  • “Particle size ≥95% through 40 mesh; bulk density reported per lot.”
  • “Granulation or dilution only by written agreement, with the carrier named.”

We supply the standard 40 mesh powder. A granulated or diluted presentation is a quotation item, not a substitution, because it carries its own specification, its own certificate lines and, for a blend, its own label. The catalog figures are on the lithium orotate product page; the salt choice and its label consequence are on the orotate versus carbonate page; the certificate lines are on the COA page; the sieve and particle procedures are in the methods library; lot release is described on the quality page. The magnesium orotate page shows how the same acid behaves when the element and the hydrate carry the fill weight instead.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation