How to prove a calcium malate lot is the neutral salt
A calcium malate lot is the neutral salt when the calcium titration is near 23.3%, the HPLC malate result accounts for the rest of the mass, the loss on drying is at or below 2.0%, and the infrared spectrum matches the reference. The calcium figure alone cannot separate the malate from the carbonate, the citrate or the hydrogen malate; the malate result and the calcium-to-malate ratio do that. A carbonate blend can be built to a calcium figure, but not to the malate figure as well.
A calcium figure near 23% and a malate peak are necessary but not sufficient; the two have to agree with each other and with the moisture.
The identity layers
A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.
| Layer | Question | Test | What it proves |
|---|---|---|---|
| Document | Is the salt named? | Name, formula, CAS number | Paperwork only |
| Calcium | How much calcium is present? | Complexometric titration | The calcium load, not the anion |
| Malate | Is the anion malate? | HPLC against a malate standard | The organic counter-ion |
| Mass balance | Do the numbers close? | Assay, loss on drying, impurities | Consistency of the figures |
| Solid form | Is it a crystalline salt or a blend? | Infrared spectrum and X-ray diffraction | The solid phase, not the purity |
The calcium-to-malate ratio
The neutral salt has one calcium ion for each malate dianion. Calcium is 23.28% of the formula mass and the malate dianion is 76.72%, so a pure lot should report those figures, adjusted for moisture and impurities, and the two should sum to approximately 100% with the loss on drying. A certificate that reports 23.0% calcium and 76.0% malate at 1.0% loss on drying is internally consistent; one that reports 23.0% calcium and 60% malate is not.
The calcium figure is a useful first screen because the common calcium salts sit at different stoichiometric values. The table is not a specification; a blend can be formulated to any figure, so the screen narrows the question rather than closing it.
| Material | Calcium by calculation | What a result near this figure suggests |
|---|---|---|
| Calcium hydrogen malate | 13.1% | The acid salt, a hydrate or a dilution |
| Calcium citrate tetrahydrate | 21.1% | The citrate, or a malate-citrate blend |
| Calcium malate, neutral | 23.3% | The salt described here |
| Calcium carbonate | 40.0% | The carbonate, or a calcium-rich blend |
| Calcium hydroxide | 54.1% | An alkaline calcium source |
| Calcium oxide | 71.5% | An alkaline calcium source |
A figure above the 24.0% top of the catalog window is the strongest warning. The neutral salt cannot reach it without a calcium-rich impurity, and the malate assay will fall in proportion. A figure below 22.0% points the other way: a hydrate, a carrier or a different salt.
The ratio is stronger than either figure alone because the two methods measure different things. The titration sees calcium, the HPLC sees malate, and the mass balance sees water. A blend has to satisfy all three at once, which is harder than satisfying the calcium window.
X-ray diffraction and the solid form
X-ray diffraction answers a different question: is the solid crystalline, and does its pattern match a reference? It can distinguish the crystalline malate from a carrier, and it can show a calcite pattern if calcium carbonate is present as a separate phase. The calcium figure cannot show a phase; the diffraction pattern can.
XRD is not a routine release test for this product. Request it when a source is new, when the calcium and malate figures disagree, or when a carbonate is suspected but the acid test is not decisive. Ask for the reference pattern and the detection limit before reading a “match” statement; a pattern without a reference proves only that the sample is crystalline.
The infrared spectrum is the routine solid-form check and is already on the catalog. It shows the malate carboxylate bands and the absence of a carbonate band at the level of the method. Neither IR nor XRD is a purity assay, and neither replaces the calcium and malate results.
What adulteration looks like
| Adulterant | What it does | Signal | Test |
|---|---|---|---|
| Calcium carbonate | Raises calcium; adds a carbonate phase | Gas in dilute acid; calcium above window | Acid test, XRD, calcium titration |
| Calcium citrate | Lowers calcium; adds citrate | Calcium near 21%; citrate by HPLC | HPLC, infrared spectrum |
| Calcium hydrogen malate | Lowers calcium to about 13% | Calcium low; malate high relative to calcium | Calcium titration, XRD |
| Calcium hydroxide or oxide | Raises calcium and pH | Alkaline slurry; calcium above window | pH, titration, XRD |
| Malic acid | Lowers calcium; acidifies | Low pH; calcium low; malate by HPLC | pH, HPLC, titration |
| Carrier or moisture | Lowers calcium and assay | Loss on drying high; assay low | Loss on drying, mass balance |
The acid test is the quickest screen for a carbonate: a few milligrams in dilute acid give bubbles for the carbonate and no bubbles for the malate. It is not quantitative and it does not detect a citrate, but it catches the simplest substitution before a laboratory result arrives.
How to write identity into the specification
- “Calcium malate, neutral salt, C4H4CaO5, CAS 17482-42-7.”
- “Calcium 22.0–24.0% by complexometric titration; assay 98.0–102.0% by HPLC, with the basis stated.”
- “Loss on drying ≤2.0%; identification by infrared spectrum and HPLC retention.”
- “Particle size ≥95% through 40 mesh; heavy metals and microbiology as listed.”
- “No calcium carbonate, calcium citrate, calcium hydrogen malate or carrier added,” unless a granulation aid is declared.
- “The certificate reports calcium, malate and loss on drying in the same lot.”
The exclusion clause is the part that prevents a blend from passing on the calcium window. The clause should be written into the purchase order and quoted on the certificate, so the laboratory knows what it is releasing against.
Five questions for the supplier
- Which salt form is this lot, and which CAS number is on the certificate?
- What is the calcium result, and which titration method produced it?
- What is the malate result by HPLC, and what standard and detection were used?
- What is the loss on drying, and is the assay reported as-is or on the dried basis?
- If the lot is disputed, will you accept a joint re-test on the retained sample, with XRD if a carbonate is suspected?
Five direct answers amount to an identity file. A single calcium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page compares the salt forms; the malate versus carbonate page covers the calcium and solubility comparison; the XRD method note, the HPLC method note and the methods section describe the tests.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation