Calcium lactate grades: the hydrate, the mesh and the pack
Calcium lactate is supplied as the pentahydrate powder at 40 mesh, and that is the grade the catalog describes. An anhydrous grade carries about 18.4% calcium against 13.0% and removes the water of crystallisation, which matters when the powder mass per serve is the constraint. Mesh, granulation and the grade paper are separate choices, and they are settled after the hydrate.
The grade question is the hydrate first and the particle size second: the mesh changes how the powder flows, while the hydrate changes how much calcium each gram carries.
Why the form comes before the grade
Calcium lactate crystallises from water as the pentahydrate, and that is the form most food and supplement specifications describe. The anhydrous salt is made by driving the crystal water off; it is a different specification with a different CAS number and a different calcium figure per gram, not a drier version of the same bag. Two suppliers can both quote “calcium lactate 99%” and be selling powders that differ by 41% in calcium per gram, so the form has to be fixed before the mesh or the pack.
Grade words are used loosely in the trade. A food grade usually points to an additive monograph such as the one behind E 327; a supplement grade points to a specification written for a dietary ingredient; technical is a different material with different impurity limits. The useful question is not which word is printed on the drum but which specification and which market the buyer is working to.
Pentahydrate and anhydrous side by side
| Property | Pentahydrate | Anhydrous |
|---|---|---|
| Formula | C6H10CaO6·5H2O | C6H10CaO6 |
| CAS number | 5743-47-5 | 814-80-2 |
| Molecular weight | 308.29 | 218.22 |
| Calcium, theoretical | 13.0% | 18.4% |
| Water of crystallisation | 29.2% | None |
| Powder per gram of calcium | 7.69 g | 5.43 g |
| Behaviour in humid air | Surface moisture and caking | Takes up water and rehydrates |
| Typical use | Tablets, capsules, sticks, liquids | Compact tablets, dry blends |
The last three rows are the ones a purchasing decision turns on. The hydrate is the heavier powder for the same calcium, and it is the more forgiving one to store. The anhydrous salt buys mass back and asks for a dry handling line in return.
Solubility, taste and flow
Both forms dissolve in water, and the solution is neutral to slightly alkaline with a mild saline note that grows with the dose. Lactate is among the more soluble calcium salts used in supplements, which is why it appears in ready-to-drink formats and sticks where calcium citrate would leave a sediment. Once dissolved, the two forms give the same calcium and lactate ions: the difference is in the powder, not in the solution.
The pentahydrate is the easier powder. It flows at 40 mesh, it is not strongly hygroscopic, and it holds its crystal water in a normal store. The anhydrous salt is hygroscopic: opened to humid air it takes water back, and a lot that has picked up water weighs more, carries less calcium per gram and can cake in the hopper. That is a handling penalty rather than a purity failure, but it has to be planned for.
Granulation is available on request. A granulated lot flows better and makes less dust, but it gives a coarser particle size and a slower dissolution in a stick. It is a separate specification, not a packing option, and it should be named before the order rather than after the trial.
What the form does to the fill
A 200 mg calcium claim needs 1,538 mg of pentahydrate at 13.0% or 1,087 mg of the anhydrous salt at 18.4%. In a 600 mg capsule that is three capsules of the hydrate against two of the anhydrous; at 500 mg of calcium it is 3.85 g against 2.72 g, which decides whether the product is a single tablet or a two-tablet serving. The arithmetic is set out in full on the pentahydrate versus anhydrous page.
The same logic runs through a stick. For a fixed sachet weight the hydrate fills more of the pack for the same claim, so the denser form either raises the calcium or leaves room for flavour and acid. What it does not do is make the powder stronger in any chemical sense: the calcium per molecule is unchanged.
What to write into the specification
- “Calcium lactate pentahydrate, CAS 5743-47-5, C6H10CaO6·5H2O.”
- “Assay 98.0–101.0% on the dried basis by complexometric titration; water 22.0–27.0% by Karl Fischer.”
- “Calcium 13.0–14.0% as-is.”
- “Identification by IR and by HPLC for lactate; calcium confirmed by the oxalate reaction.”
- “≥95% through 40 mesh; Pb ≤3, As ≤2, Cd ≤1, Hg ≤0.1 mg/kg.”
- “No anhydrous salt, calcium carbonate or other calcium source added.”
The exclusion clause is not decoration. A blend of the pentahydrate with a denser calcium salt can be made to land inside the calcium window, and the clause plus the water figure is what catches it: the calcium rises while the water falls.
When the other form is the wrong choice
If the specification or the customer names the pentahydrate, the anhydrous salt is not a substitution, even though it is the same molecule once dissolved: the declared ingredient and the weighed ingredient would differ. If the plant is humid and the powder is weighed by hand, the hygroscopic form is the harder material to control, and a caked lot can lose more in rejected batches than the mass it saves.
The reverse holds too. A buyer who needs a compact tablet or a dry blend with a low powder mass should not accept the pentahydrate and correct the dose afterwards; the fill weight and the tablet size are set before the blend is written. The catalog here is the pentahydrate at 40 mesh, and the anhydrous grade is a separate purchase with its own certificate.
The product hub carries the catalog limits; the COA page shows how the hydrate and the water are reported; the compliance page covers the two EU routes. The nearest alternative salts are set out on the calcium carbonate and calcium gluconate pages, where the calcium figure per gram is 39–41% and 8.5–9.5% respectively.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation