How to prove a lot is calcium citrate anhydrous
Calcium titration will pass the anhydrous salt, the tetrahydrate and several other calcium powders, so the certificate needs tests that rule those alternatives out. This product is proved by the combination of a calcium figure near 24.1%, a citrate reaction and infrared match, and loss on drying at or below 1.0%. The water result is the one that removes the tetrahydrate, which would otherwise sit inside the 21.0–24.0% calcium window.
Calcium alone cannot name the hydrate: the 21.0–24.0% window admits the tetrahydrate, and the 1.0% loss-on-drying limit is what excludes it.
The identity layers
Read the certificate as a process of elimination rather than a single tick. Each layer narrows the list of materials that could produce the number above it, and a layer that is missing leaves the alternatives open.
| Layer | Question | Test | What it proves |
|---|---|---|---|
| Document | Is the hydrate named? | Name, CAS number, formula | Paperwork only |
| Calcium | Is calcium inside the window? | Complexometric titration | Quantity, not the anion or the hydrate |
| Citrate | Is the anion citrate? | Reaction and infrared spectrum; HPLC if quantitative | The salt family |
| Water | Is it the anhydrous form? | Loss on drying; TGA or Karl Fischer if disputed | The hydrate state |
| Crystal | Which solid form is present? | X-ray diffraction | Anhydrous against tetrahydrate; carbonate or oxide |
Calcium is the broadest filter. Citrate narrows it to the salt family. Water names the hydrate, and the crystal layer can confirm what the water figure implies. None of the four quantitative layers proves the others.
The calcium-to-citrate ratio
Charge balance fixes the ratio: three calcium ions to two citrate anions, or 1.5 calcium per citrate. In the anhydrous formula that works out to about 24.1% calcium and 75.9% citrate; the tetrahydrate carries about 21.1% calcium, 66.3% citrate and 12.6% water. The ratio is the same in both hydrates; only the water changes the percentages.
A worked check makes the arithmetic usable. If a lot reports 23.9% calcium and 75.2% citrate, divide each by its molar mass: 23.9 ÷ 40.078 = 0.596 mol calcium, 75.2 ÷ 189.1 = 0.398 mol citrate, ratio 1.50. A ratio near 1.33 means extra citrate, which points to added citric acid; a ratio near 1.60 means extra calcium from another salt. The ratio tests consistency, not potency.
A routine certificate may not quantify citrate at all. If the proportion matters to the purchase, request a citrate assay by HPLC or titration and name the method; otherwise the identity rests on the reaction and the infrared spectrum, which show that citrate is present but not how much.
XRD, TGA and the crystal form
X-ray diffraction sees the lattice. The anhydrous salt and the tetrahydrate have different patterns, and a scan can confirm the hydrate independently of the water figure. The same scan can reveal crystalline calcium carbonate as calcite, with a reflection near 29.4° two-theta, or calcium oxide as lime, with its own peaks.
Thermogravimetry adds the temperature dimension. A tetrahydrate loses its water in a step that an anhydrous lot does not show, and the size of the step estimates the amount. Loss on drying is the routine release test; TGA is the referee when the form is disputed.
Ask for the reference pattern, the sample preparation and the detection limit. A “match” without the pattern is a conclusion, and a “not detected” without a limit describes the method's sensitivity rather than the sample. XRD is not a routine release test here, but it is the direct answer when the question is crystal form.
What adulteration looks like
| Adulterant | What it does | Signal | Test |
|---|---|---|---|
| Tetrahydrate | Raises water and lowers calcium | Loss on drying around 10–13% | Loss on drying, TGA, XRD |
| Calcium carbonate | Raises calcium; adds no citrate | High calcium, no citrate, gas in acid | Citrate identity, XRD for calcite |
| Calcium oxide | Raises calcium; alkaline slurry | Very high calcium, high pH | XRD for lime, pH |
| Citric acid | Raises citrate; lowers the ratio | Calcium-to-citrate ratio below 1.5 | Citrate assay, ratio |
| Surface water | Raises loss on drying; lowers as-sold calcium | Dried-basis calcium normal | Loss on drying, Karl Fischer |
The first row is the most likely substitution because it is the same salt, and the calcium window can accept it. Water is the first screen. Carbonate and oxide are the next risks; both raise calcium, but carbonate removes the citrate and oxide lifts the pH. Appearance adds little, because white to off-white covers a wide family of powders.
How to write identity into the specification
- “Calcium citrate anhydrous, Ca3(C6H5O7)2, CAS 813-94-5.”
- “Calcium 21.0–24.0% by complexometric titration, reported on the material as sold.”
- “Loss on drying ≤1.0%, with the drying conditions stated; no tetrahydrate above that limit.”
- “Identification by calcium reaction, citrate reaction and infrared spectrum.”
- “Citrate content by HPLC on request, with the calcium-to-citrate ratio reported.”
- “No added calcium carbonate, calcium oxide or citric acid; XRD screen on request.”
A calcium-and-mesh specification could describe several calcium powders. The hydrate, the citrate test and the adulterant clause are what narrow it to this one.
Five questions for the supplier
- Which hydrate does this lot represent, and what loss on drying is on its certificate?
- What calcium figure, method and basis are reported?
- How was citrate identified, and is a quantitative citrate result available?
- Does the file contain an XRD or TGA result for the solid form, and what detection limit is stated?
- Has any carbonate, oxide or citric acid been added, and what evidence backs that answer?
Answers to those five questions build an identity file; a calcium percentage alone does not. The certificate lines are on the COA page; the hydrate comparison is on the grade page; the narrow comparison is on the anhydrous versus tetrahydrate page; the methods are under analytical methods; the catalog figures are on the product hub; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation