02.1 Anhydrous vs tetrahydrate

Calcium citrate anhydrous vs tetrahydrate: water, calcium and the label

Technical document 02.1 · Reviewed 2026-11-20 · Calcium Citrate Anhydrous

On this page
  1. The water of crystallisation
  2. What the water does to the calcium figure
  3. What the label has to declare
  4. Dose and the dosage form
  5. Writing the specification
  6. What changes when you switch

Calcium citrate anhydrous and calcium citrate tetrahydrate are the same calcium salt with four molecules of water between them. The water is 12.6% of the tetrahydrate's mass, so the anhydrous form carries about 24.1% calcium against 21.1%, and the tetrahydrate needs about 14.5% more powder for the same claim. The difference shows up in the loss-on-drying limit, the dose arithmetic and the label, not in the citrate anion.

In one line

Four water molecules are 12.6% of the tetrahydrate's mass, and that water changes the calcium figure, the powder weight and the label arithmetic.

The water of crystallisation

The two hydrates are not two purities of the same powder. In the tetrahydrate, four water molecules sit in defined sites in the crystal; the anhydrous salt has none. The water is part of the crystal, not free moisture in the blend, and it leaves at a characteristic temperature when the crystal is dried. The formula mass is 570.49 g/mol for the tetrahydrate and 498.44 g/mol for the anhydrous salt; the 72.05 g/mol gap is the four water molecules.

The catalogs turn that into a release test. Loss on drying is ≤1.0% for the anhydrous product and ≤13.0% for the tetrahydrate. The tetrahydrate's theoretical water is 12.6%, so its 13.0% limit covers the lattice water plus a little surface moisture. The anhydrous limit leaves almost no room for surface water, which is why the pack and the storage condition belong in the specification rather than in a warehouse note.

A water figure near 12% is not a wet anhydrous lot; it is the other hydrate. A water figure near 0.5% is not a better grade of tetrahydrate; it is the anhydrous salt. The number has to be read with the hydrate named on the order.

What the water does to the calcium figure

Both forms have the same 3:2 calcium-to-citrate ratio. The calcium percentage differs because the water adds mass to the formula without adding calcium, so the same three calcium ions are spread over a larger molecule.

Calcium citrate anhydrous against the tetrahydrate
PropertyAnhydrousTetrahydrate
FormulaCa3(C6H5O7)2Ca3(C6H5O7)2·4H2O
Molecular weight498.44570.49
CalciumAbout 24.1%About 21.1%
Water of crystallisationNone12.6% by mass
Loss on drying limit≤1.0%≤13.0%
Calcium in 1 g of saltAbout 241 mgAbout 211 mg
Salt for 500 mg calciumAbout 2.07 gAbout 2.37 g

Those two calcium figures are the whole practical difference. The citrate anion, the taste and the acid behaviour are the same; the mass per calcium ion is not. A buyer who compares the two products on calcium percentage alone is comparing the hydrate, not the quality.

What the label has to declare

In the European Union the permitted-source entry in Annex II to Directive 2002/46/EC is written for “calcium salts of citric acid”, not for a named hydrate. The ingredient list names the source as the law names it; “anhydrous” is a specification description, not a separate source entry. The EU declaration gives a milligram figure for calcium and a percentage of the 800 mg reference intake.

On the US side, the Supplement Facts panel declares elemental calcium and names the salt in the ingredient list; the Daily Value is 1,300 mg.

Neither market requires the word “anhydrous” in the source name, but the number in the panel has to match the powder that was weighed. That is the label consequence: the hydrate decides whether a declared salt weight delivers 241 mg or 211 mg of calcium per gram.

Two label styles make the arithmetic visible. A label that declares 500 mg of elemental calcium needs about 2.07 g of the anhydrous salt or 2.37 g of the tetrahydrate. A label that declares 1,000 mg of calcium citrate delivers about 241 mg of calcium from the anhydrous salt or 211 mg from the tetrahydrate. The hydrate belongs in the specification, the batch record and the label review, even when it does not appear on the front of the pack.

Dose and the dosage form

A 500 mg calcium claim is a useful fixed point. At 24.1% it needs about 2.07 g of the anhydrous salt; at 21.1% it needs about 2.37 g of the tetrahydrate. The 300 mg difference is roughly half a 650 mg capsule fill. A two-capsule serving of the tetrahydrate can become a smaller capsule count with the anhydrous salt, or the same count with a lower fill weight.

At a fixed salt weight the difference runs the other way: 1,000 mg of anhydrous salt delivers about 241 mg calcium, and 1,000 mg of tetrahydrate about 211 mg. A formula that switches hydrate without changing the weigh-up changes the calcium claim by about 30 mg per gram of salt. That is a label change, not a rounding difference.

Choose the anhydrous form when the calcium claim is fixed and the fill or tablet weight is tight, or when the low water limit is the point of the purchase. Choose the tetrahydrate when the label, the process and the validated fill are already built around it. Neither is a drop-in for the other at the balance.

Writing the specification

  • “Calcium citrate anhydrous, Ca3(C6H5O7)2, CAS 813-94-5.”
  • “Calcium 21.0–24.0% by complexometric titration, on the material as sold.”
  • “Loss on drying ≤1.0%, with the drying conditions stated on the certificate.”
  • “Identification by calcium reaction, citrate reaction and infrared spectrum.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No tetrahydrate above the water limit; no carbonate, oxide or citric acid addition.”

A specification copied from the tetrahydrate will fail the anhydrous product at the water line, and one copied the other way can accept the tetrahydrate inside the anhydrous calcium window. The hydrate, the calcium window and the water limit belong on the same page, and the label arithmetic belongs beside them.

What changes when you switch

A change of hydrate is a change of mass, not a change of salt. The powder weight per claim, the capsule count or tablet weight, the water limit, the flow of the lot, the label arithmetic and the customer's change control all move together. The stability file moves too, because the anhydrous form is the more hygroscopic of the two.

Trial the new mass before the label is printed: fill or compress it, check the taste and the pH in the matrix, and repeat the water test after storage. A switch that looks neutral in a spreadsheet is a new specification and a new label revision. The anhydrous product hub carries the catalog figures; the tetrahydrate product page carries the parent specification; the method notes cover the water and citrate tests; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation