Calcium citrate anhydrous or tetrahydrate: choosing the hydrate
Both products are calcium citrate; the difference is how much water sits inside the crystal. The anhydrous salt is Ca3(C6H5O7)2 with about 24.1% calcium and no water of crystallisation, while the tetrahydrate adds four water molecules, 12.6% of its mass, and carries about 21.1% calcium. The catalog numbers follow: 21.0–24.0% calcium and ≤1.0% loss on drying for the anhydrous product, 21.0–22.0% and ≤13.0% for the tetrahydrate.
Four molecules of water are 12.6% of the tetrahydrate's mass: they lower the calcium figure, raise the powder weight for a given claim, and change the label arithmetic.
One salt, two crystal forms
Calcium citrate can crystallise in more than one hydrate state. In the tetrahydrate, four water molecules occupy defined sites in the lattice; the anhydrous salt has no such water. This is a crystal difference, not a coating or a blend, and it survives every calculation that starts from the formula mass.
The commercial anhydrous grade is commonly made by driving the lattice water out of the tetrahydrate. The dryer has to go far enough to clear the water and gently enough to leave the citrate intact; the ≤1.0% loss-on-drying gate is the evidence that the step worked. A lot that still holds lattice water is the other product.
Both grades are milled to 80 mesh for capsules, tablets and sticks. The choice starts with the calcium claim and the space in the unit, then moves to the label and the purchase order.
The two products side by side
| Property | Anhydrous | Tetrahydrate |
|---|---|---|
| Formula | Ca3(C6H5O7)2 | Ca3(C6H5O7)2·4H2O |
| Molecular weight | 498.44 | 570.49 |
| Calcium | About 24.1% | About 21.1% |
| Water of crystallisation | None | 12.6% by mass |
| Catalog calcium window | 21.0–24.0% | 21.0–22.0% |
| Loss on drying | ≤1.0% | ≤13.0% |
| Calcium in 1 g of salt | About 241 mg | About 211 mg |
| Salt for 500 mg calcium | About 2.07 g | About 2.37 g |
The last two rows are what reach the label and the capsule. The same calcium claim needs about 14.5% more tetrahydrate, or the same weight of tetrahydrate delivers about 30 mg less calcium per gram. That is stoichiometry, not a purity grade.
Solubility, moisture and flow
Water solubility is low for both forms, around 1 g/L, and rises in dilute acid. Neither contains carbonate, so neither fizzes in acid. Solubility is pH dependent, and the citrate can leave solution as the salt approaches neutral; that matters in a drink and little in a capsule.
The anhydrous salt is the one that wants its water back. Left open in humid air it takes up moisture and the loss on drying climbs; the tetrahydrate already has its lattice water and mostly collects surface moisture. This is why the foil pouch and the drum liner matter more for the anhydrous grade, and why an opened pack needs a new seal rather than a folded top.
Flow and bulk density depend on milling and sieving. Both products are catalogued at 80 mesh, with granulation on request. Do not assume the anhydrous salt is denser or freer-flowing; ask for the bulk density of the lot and trial it in the press or the capsule filler.
Dose arithmetic and the label
Start with 500 mg of calcium. At 24.1% the anhydrous salt needs about 2.07 g; at 21.1% the tetrahydrate needs about 2.37 g. The 300 mg gap is roughly half a 650 mg capsule fill, enough to change the unit count or the tablet weight. At a fixed 1,000 mg of salt, the anhydrous form delivers about 241 mg calcium and the tetrahydrate about 211 mg.
A label that declares elemental calcium keeps the claim and changes the powder weight when the hydrate changes. A label that declares the salt weight changes the calcium delivered. The two styles lead to different specifications, and a purchase order that names only “calcium citrate” does not say which one is being bought.
Water of crystallisation is not free water in the blend; it is part of the crystal. The tetrahydrate is therefore not a “wet” ingredient in a dry mix, and the anhydrous form is not automatically required for every low-moisture formula. The reason to choose anhydrous is mass: more calcium per gram, less powder per claim, and a tighter water gate.
What to write into the specification
- “Calcium citrate anhydrous, Ca3(C6H5O7)2, CAS 813-94-5.”
- “Calcium 21.0–24.0% by complexometric titration, reported on the material as sold.”
- “Loss on drying ≤1.0%, with the drying temperature and time stated on the certificate.”
- “Identification by calcium reaction, citrate reaction and infrared spectrum; conforms to reference.”
- “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
- “No tetrahydrate above the water limit; no carbonate, oxide or citric acid added.”
Put the hydrate in the product name, not in a footnote. A specification that opens with “calcium citrate” and gives only a calcium window can be met by either hydrate; the water limit is the line that makes it specific.
When the other hydrate is the wrong choice
If the label, the fill weight or the validated process is built on the tetrahydrate, the anhydrous salt is a change control, not a drop-in. The tablet may compress differently, the capsule count may fall and the calcium per unit may rise. Those are formulation changes even though the parent salt is the same.
If a customer specification or a compendial monograph names the tetrahydrate, do not substitute the anhydrous form against that document. If the calcium claim is fixed and the fill is already at its limit, the anhydrous form is the one that fits; if the salt weight is fixed and the label expects the tetrahydrate's calcium, the anhydrous form over-delivers. Put the choice in writing before the first lot is made.
The catalog figures are on the anhydrous product page. The tetrahydrate specification is on the calcium citrate product page; the narrow comparison is on the anhydrous versus tetrahydrate page; the water test is covered under analytical methods; release practice is on the quality page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation