06 Identity & adulteration

How we prove a lot is nervonic acid

Technical document 06 · Reviewed 2026-11-19 · Nervonic Acid

On this page
  1. Four questions, four kinds of evidence
  2. The ratios that name the material
  3. X-ray diffraction: what it can and cannot show
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

Four independent checks have to agree before a nervonic acid lot can be called the named material. The paperwork names the C24:1 acid and its CAS number; the chromatogram carries a main peak at the C24:1 retention with the right neighbours; the acid value reads like a free acid rather than an ester; and the mass balance closes against the moisture figure. An assay on its own cannot tell chain length, configuration or an esterified dilution apart.

In one line

Identity is four agreeing measurements: the peak says C24:1, the neighbours say the fraction, the acid value says free acid, and the balance says nothing was added.

Four questions, four kinds of evidence

A certificate can show the right name and still prove nothing. The four layers below are separate questions, each needing its own evidence, and a supplier who answers only the first of them has described paperwork rather than powder.

Four layers of nervonic acid identity
LayerWhat it asksEvidenceWhat it establishes
DocumentAre the acid and the chain named?Name, CAS 506-37-6, formula, sourcePaperwork only
ChromatogramIs the main peak C24:1?GC-FID retention and GC-MS confirmationThe chain length and the configuration claimed
Acid valueIs it a free acid?Titration, mg KOH/gFree acid against ester or glyceride
Mass balanceIs anything else in the drum?Assay, moisture, ash and acid value togetherThat the numbers describe one material

The ratios that name the material

On a long polar column the methyl ester of C24:1 elutes just before C24:0, with C22:1 well before both. That order makes the ratios more revealing than the headline figure. The C24:1 to C24:0 ratio says how hard the enrichment cut was run, and a falling ratio points to a saturated fraction rather than to a synthesis error. The C22:1 peak says whether the starting oil was carried through the cut.

The acid value is the second ratio. The calculated value for pure nervonic acid is about 153 mg KOH/g, and a 90% free acid with a neutral balance should read near 138. A lot that reports 90% by GC and an acid value near 153 is a mixture of free acids; a lot that reports 90% and an acid value near 138 has roughly a tenth of its mass as glyceride or ester. Both can be legitimate purchases, and only the acid value says which one is in the drum.

The third check is the moisture. Loss on drying is limited at ≤1.0%, so the as-is and dried assays sit close together, but a lot that reports an assay without a moisture figure has left a small gap in the balance. A high loss on drying with a normal anhydrous assay is a wet powder, not a concentrated one.

X-ray diffraction: what it can and cannot show

A long-chain fatty acid is crystalline at room temperature, so the powder diffracts. The pattern is dominated by the chain packing, and the long spacings of C24:0 and C24:1 are almost the same. That means XRD can show that the material is crystalline and can compare the solid form of two lots, but it cannot prove the chain length or the cis double bond. It also cannot replace GC for the assay.

What XRD does well is the dilution question: a powder cut with silica or maltodextrin shows an amorphous halo alongside the acid reflections, and a lot that has been melted and re-solidified can show a different reflection set from the reference. A “conforms” statement that arrives without the pattern and the detection limit is worth little. For a solid-state question the melting range of 42–44 °C is usually the simpler screen.

What adulteration looks like

Substitution routes for nervonic acid and the signal for each
RouteWhat it doesSignalTest
Other monounsaturateOleic or erucic acid replaces C24:1Extra C18:1 or C22:1 peak; C24:1 share fallsFull GC profile
Saturated C24:0 cutRaises the melting range; lowers the C24:1 ratioMelting point above 44 °C; ratio downGC plus melting point
Esterified materialEthyl ester or glyceride passes an assayAcid value below 138 at a 90% assayAcid value, saponification value
Carrier dilutionSilica or maltodextrin adds massAssay low; ash or XRD haloMass balance, ash, XRD
Oxidised materialDouble bond attacked; colour and odourPV and anisidine up; yellowingPV, anisidine, appearance

The first route is the most likely one, because oleic and erucic acids are widely available and liquid, and neither would be visible in an appearance check. GC separates them by a wide margin, so a full profile catches it. The quiet route is the second: a saturated cut keeps the white waxy appearance and can pass a loose melting range.

Names cause their own confusion. Selacholeic acid is a synonym for nervonic acid, “nervon” is a cerebroside rather than the acid, and trans-15-tetracosenoic acid is the same chain length with a different configuration. A certificate that uses one of those names without the CAS number is describing something the buyer has to check.

How to write identity into the specification

  • “Nervonic acid (cis-15-tetracosenoic acid), CAS 506-37-6, C24H46O2, free acid.”
  • “C24:1 ≥90.0% by GC-FID; the column, the standard and the ester factor stated.”
  • “C24:0 and C22:1 reported; limits agreed for each.”
  • “Acid value reported in mg KOH/g and consistent with the free acid at the declared assay.”
  • “Melting point 42–44 °C; loss on drying ≤1.0%.”
  • “No carrier, and no ester above the agreed limit.”

Five questions for the supplier

  1. Which peak on the chromatogram is C24:1, and what column and standard produced it?
  2. What are the C24:0 and C22:1 figures on this lot, and what limits apply?
  3. What is the acid value, and does it match a free acid at this assay?
  4. What moisture figure was recorded, and was the assay taken as received or after drying?
  5. If we disagree about a result, will you re-test the retained sample jointly?

Five answers of that kind build an identity file. One percentage does not. Catalog data is published on the product hub; the reporting format is on the COA page; the chain-length comparison is on the nervonic versus oleic page; the profile-as-fingerprint approach is shown on the flaxseed oil powder identity page; the diffraction method is described in the XRD method note.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation