03 Stability

Borage oil stability: oxidation, pack and shelf life

Technical document 03 · Reviewed 2026-11-19 · Borage Oil

On this page
  1. The neat oil in its sealed pack
  2. Blends, emulsions and softgel fills
  3. What moves the oil in storage
  4. A stability protocol for borage oil
  5. What the finished formula does
  6. Setting the retest period

Borage oil is an oxidation-prone seed oil. Its GLA carries three double bonds and its linoleic acid two, so oxygen, light and warmth attack the oil before the fatty-acid assay shows anything unusual. Peroxide value rises first, p-anisidine value follows as secondary aldehydes form, and free fatty acid climbs when moisture reaches the oil. How long it holds depends on the container, the headspace and the storage temperature.

In one line

Borage oil fails by oxidation before it fails by assay, so peroxide value, p-anisidine value and free fatty acid are the early signals the pack has to control.

The neat oil in its sealed pack

The release limit for moisture is ≤0.1%. That is a gate at filling, not a buffer against a humid store: residual water and water vapour both drive hydrolysis, and free fatty acid is the value that climbs. A drum left open in a damp room is no longer in the condition it was tested under. Keep the 1 kg amber bottle and the 25 kg HDPE drum sealed, lined and dry.

Oxygen matters more than moisture here. Oxidation starts at the oil surface and continues in whatever air sits above it, so a full drum ages more slowly than one that has been drawn down. Nitrogen can displace that air at filling, but the flush has to be specified and checked; without a measurement it is an assumption. Once a pack is open, transfer the remainder to a smaller container that leaves little headspace.

Light is the third variable. Oil in a clear bottle on a lit shelf oxidises through the glass, so amber glass or an opaque secondary pack is part of the specification. Warmth accelerates the same reactions; a store near a heater is a different condition from a temperature-controlled room.

Blends, emulsions and softgel fills

Borage oil is not water-soluble and not supplied as an aqueous solution. The systems that matter are oil blends, oil-in-water emulsions and softgel fills, and each changes the oxidation rate. In a blend, the most unsaturated oil usually governs the induction period, and a small share can pull the whole blend down.

In an emulsion the oil is dispersed into small droplets, so the interfacial area is large and oxygen, light and trace metals meet the oil at the interface. Emulsifier choice, pH, homogenisation energy and antioxidant strategy outweigh the bulk oil's own result. An emulsion stable on the bench can still develop a painty note in a pack; run the shelf-life study in the emulsion, not only on the bulk oil.

A softgel shell limits oxygen transfer but does not stop it, and it can carry moisture into the fill. The fill's peroxide and p-anisidine values at release and after storage are the evidence; the shell colour and the fill odour are the early warning. A powder's matrix, oil load and seal decide the rate.

What moves the oil in storage

What changes borage oil during storage
FactorEffectControl
OxygenRaises peroxide value, then p-anisidine valueNitrogen flush; low headspace; sealed pack
LightAccelerates oxidation at the surfaceAmber glass or opaque secondary pack
HeatRaises the rate of oxidation and hydrolysisCool store; short holds; no hot loading bay
MoistureDrives hydrolysis and raises free fatty acidDry store; closed liner; ≤0.1% at release
Metal ionsCatalyse oxidation at trace levelsStainless steel or glass contact; avoid iron and copper
Repeated openingReplaces the headspace with airSmaller packs; decant into a full container

The factors reinforce one another: a warm, lit store holding a part-used drum is the hardest case. The question is not whether the oil is stable in the abstract, but for how long, in which pack and under which conditions.

A stability protocol for borage oil

A usable protocol fixes four things: the container, the climate, the sampling times and the tests. A common design uses 25 °C/60% RH long term, 30 °C/65% RH intermediate and 40 °C/75% RH accelerated. Include a light-exposure arm: an incubator kept dark cannot reveal a photochemical failure. If the oil is sold in a softgel, blend or emulsion, study that matrix as well.

Test peroxide value, p-anisidine value, free fatty acid, moisture and appearance at every point, and run the full fatty-acid profile at the first and last time points to check the GLA figure and identity. Tocopherols are worth measuring if the oil is sold on its minor components or an antioxidant has been added. The report should give individual results, not a pass statement, tied to the pack, lot family and storage condition.

Sampling has to be representative: a top-of-drum sample is not the same as one drawn after mixing, and a sample left open on the bench has already begun to oxidise. The protocol should say how the sample was taken, stored before the test and how long it waited.

What the finished formula does

A softgel fill is the most common format for borage oil, and the shell is a barrier rather than a seal. Gelatin and plant shells transmit some oxygen and moisture, and the seam is the weak point. Measure the fill at release and at the end of the study, and inspect the shell for discolouration, sticking and leakage.

Blended with a more saturated oil, the blend may oxidise more slowly than borage alone but not as slowly as the saturated oil, and the label must declare the blend in descending order. An emulsion adds the interface and the aqueous phase, and a powder adds the carrier and the drying step. Any antioxidant is part of the specification: mixed tocopherols, rosemary extract or another system should be named with its level, and the label must reflect it.

An antioxidant slows oxidation; it does not reverse it. Adding tocopherol to an oil that has already reached a high peroxide value does not restore the specification, and it can change the colour and the analytical result. Decide the antioxidant system before the stability study, not after a failing result.

Setting the retest period

No single shelf life applies to borage oil, because the pack, the headspace and the storage condition decide it. A retest period has to rest on data from the same pack; a number published without the pack and condition is only an assertion. Refined oil usually starts with a lower peroxide value and may hold its specification longer in the same pack, but that is a data question, not a rule.

Before any extension, the retained sample is re-tested at the end of the retest period. A bulk result does not transfer automatically to a repacked bottle or to a softgel, and one customer's storage condition does not transfer. The delivery documents should state the lot, the production date and the retest date, and the buyer should confirm the remaining shelf life at delivery.

The catalog specification is on the borage oil product page. The release tests are described on the COA page, the pack sizes and lead time are on the MOQ page, the analytical methods are indexed under methods, and the release and retained-sample workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation