06 Identity & adulteration

How we prove an algal DHA oil lot is DHA

Technical document 06 · Reviewed 2026-11-20 · Algal DHA Oil

On this page
  1. The four identity layers
  2. The ratios inside the profile
  3. X-ray diffraction and the solid-state question
  4. Substitutions and their signals
  5. How to write identity into the specification
  6. Five questions for the supplier

An algal DHA oil lot is identified by its whole fatty-acid profile, not by a single DHA percentage. The GC run should show DHA at 35.0–45.0%, EPA at or below 3.0%, a measurable DPA fraction and the saturated and monounsaturated acids that belong to the algal oil; a sterol pattern and the oxidation figures then separate a genuine algal oil from a blend. The DHA figure alone can be reached by adding DHA to another oil.

In one line

DHA can be added to an oil; only the whole fatty-acid profile, the sterol pattern and the oxidation figures show that the oil is algal and has been kept.

The four identity layers

A certificate can carry the right name and still leave the oil unproven. Each layer below answers a different question, and each needs its own measurement. A supplier who stops at the first has shown paperwork, not a sample.

Four layers of algal DHA oil identity
StageQuestion it answersMeasurementWhat it shows
DocumentIs the material named?Product name, algal source, CAS 6217-54-5Paperwork only
ChromatographyIs the fatty-acid profile algal?GC-FID of methyl esters, full profileThe oil's composition, not its source
SterolsIs another oil present?Sterol profile by GCVegetable-oil dilution
ConditionHas the oil been kept?PV, p-AV, FFA, moisture, appearanceOxidation and hydrolysis

The ratios inside the profile

The profile is a set of ratios, and the ratios are what a single DHA result hides. At the lowest DHA figure and the highest EPA figure the catalog allows, 35.0% and 3.0%, the ratio is about 12:1; at 45.0% DHA with EPA at 3.0% it is about 15:1. An algal oil is DHA-dominant in that way. A fish oil is not: it carries a larger EPA share, so a DHA/EPA ratio far below the algal range is a signal that the source or the blend has changed.

The rest of the profile matters as much. Algal oil carries palmitic and myristic acids and a low level of oleic acid; a large linoleic acid peak points to a vegetable oil such as sunflower or soy, which is a common diluent. DPA is reported in the same run, and its presence at a low level is consistent with algal oil; it is not a release limit in the catalog. None of these ratios is a purity assay on its own. They are a screen that says whether the DHA figure is plausible for the oil, and they become evidence when the chromatogram is supplied with the result.

Check the basis before comparing ratios. A profile normalised to peak area describes the composition of the fatty-acid fraction, while an internal-standard result describes grams per 100 g of oil. The two are close when the oil is pure and diverge when it is diluted or when the injection is off. The certificate should name the basis, and the ratios should be calculated from the same run.

X-ray diffraction and the solid-state question

An oil has no crystal lattice at room temperature, so X-ray diffraction is not an identity test for algal DHA oil as sold. The technique answers a solid-state question: is a powder crystalline, and does its pattern match a reference? It belongs to the spray-dried form, where it can distinguish a crystalline carrier or a crystalline fraction from an amorphous matrix, and it can compare lots from two sources. It does not measure the fatty-acid profile and it does not prove the algal source.

For the oil, the practical physical checks are different. FTIR confirms the ester and unsaturation bands, a cold test describes how the oil crystallises when chilled, and viscosity and appearance describe handling. None of them replaces the GC profile. If a supplier offers an XRD “match” for an oil, ask what was actually tested; the answer is usually the carrier or a crystallised fraction, not the oil in the bottle.

Substitutions and their signals

Signals of a substitution in algal DHA oil
AdulterantWhat it doesSignalTest
Vegetable oilDilutes DHA; adds linoleic and oleic acidsLarge C18:2 peak; sterol pattern changesFull GC profile; sterols
Fish oilRaises EPA; changes the DPA patternDHA/EPA ratio falls below the algal rangeGC profile against the EPA limit
DHA concentrateKeeps the DHA figure; changes the rest of the profileDHA passes, minor acids do not fitFull profile; source traceability
Oxidised oilFresh oil blended to hit PV or FFAp-Anisidine value and TOTOX stay highPV, p-AV, FFA and TOTOX
WaterRaises moisture and hydrolysisMoisture above 0.1%; FFA risingKarl Fischer; FFA titration

Colour is the weakest signal. A pale yellow to golden oil covers a wide range, and a blend can be matched to it. The stronger signals are the linoleic acid level, the DHA/EPA ratio, the sterol pattern and the oxidation pair. A certificate that reports appearance and DHA but not the full profile has not tested the substitution that matters most.

How to write identity into the specification

  • “Algal DHA oil from the named strain; DHA 35.0–45.0% by GC; EPA ≤3.0%; DPA reported.”
  • “Full fatty-acid profile reported with the chromatogram; GC setup and basis stated.”
  • “Free fatty acid ≤0.50%; peroxide value ≤5.0 meq O₂/kg; moisture ≤0.1%.”
  • “No added carrier oil; antioxidants declared if present.”
  • “Sterol profile available on request; source statement and fish-free statement on file.”
  • “Lot code, manufacture date and pack on the certificate and the retained sample.”

Five questions for the supplier

  1. Which algal strain and process produced this lot, and is that on the source statement?
  2. Can you provide the full GC-FID profile and chromatogram, not only the DHA percentage?
  3. What are the EPA and DPA figures from the same run, and what is the DHA/EPA ratio?
  4. What are the peroxide, p-anisidine, free fatty acid and moisture results for this lot, with test dates?
  5. If identity is contested, will you re-test the retained sample jointly?

Five direct answers make an identity file; one DHA percentage does not. The product hub holds the catalog specification; the COA page places each figure on the certificate; the powder page covers the carrier-based form; the methods section explains the GC work; the quality page describes the retained sample.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation