Algal DHA oil grades: DHA content, form and fill weight
Algal DHA oil is standardised on its DHA content, and the catalog range is 35.0–45.0% by GC with EPA ≤3.0%. Within that range a 45% oil carries 450 mg of DHA per gram and a 35% oil carries 350 mg, so a 200 mg DHA declaration needs 0.44 g or 0.57 g of oil. The physical form is the second decision: the catalog product is a neat oil, and an oil supplied on a carrier is a separate specification with its own DHA basis.
The grade of an algal DHA oil is its DHA content and its physical form; a 35% oil and a 45% oil are the same material at different standardisations, not different products.
Why the DHA figure is the grade
The oil comes out of the algal fermentation with a natural DHA content, and the supplier standardises it to a target by selecting lots, blending them or concentrating the fatty acids. The 35.0–45.0% window is wide enough that two compliant lots can differ by nearly 30% in DHA per gram, which is why the target figure belongs in the order and not only in the specification range. The grade is a concentration, not a purity statement: a 45% oil is not “purer” than a 35% oil, it carries more DHA and less of the other fatty acids per gram.
Two things are sometimes sold under the same name. A diluted oil has a carrier oil added to bring the DHA down to a lower figure; that is a formulated blend, not the catalog oil, and its ingredient list has to name the carrier oil. An oil on a carrier is the oil absorbed into a powder matrix, so its DHA is expressed on the powder and its handling is dry. Both are legitimate purchases, but neither is a different grade of the same neat oil.
The catalog oil and the forms it is confused with
| Form | DHA basis | DHA per gram | What changes |
|---|---|---|---|
| Catalog oil, 45.0% result | GC, oil as sold | 450 mg | Less oil mass per declared dose |
| Catalog oil, 35.0% result | GC, oil as sold | 350 mg | More oil mass for the same dose |
| Catalog oil, 40% result | GC, oil as sold | 400 mg | Same specification, different fill weight |
| Oil on a carrier, on request | Set by the oil load | Below the neat oil | Powder handling, carrier on the label |
| Oil diluted with a carrier oil | Declared blend | Set by the blend | Not the catalog grade; ingredient list changes |
The table is arithmetic, not a product list. A 40% result is an example inside the range, not a separate grade. A diluted oil is outside the catalog specification whatever its DHA figure, because the catalog oil has no added carrier. The first three rows describe the same product at different points in its range; the last two describe different products.
What the oil is like to handle
The catalog oil is clear to slightly hazy and pale yellow to golden. It is insoluble in water and soluble in fats and organic solvents, so it suits a softgel fill or an oil blend and does not suit a clear aqueous drink without an emulsifier. Cloudiness at low temperature is normal for a highly unsaturated oil and reverses on warming; it is not an identity failure, but the oil should be warmed and mixed before dispensing so that the fill is uniform.
The 1 kg amber bottle is the trial and small-batch pack, and the amber wall is part of the protection against light. The 25 kg HDPE drum is the production pack; the inner liner and the headspace decide how much oxygen the oil meets in storage. Neither pack is a reason to leave the oil open: an oil that is pumped from an open drum in a warm room picks up oxygen and moisture at the surface, and the pump and the line should be closed where the process allows.
The dose arithmetic
The label declares a mass of DHA, and the oil weight follows from the DHA content of the lot. The calculations below are before any overage the brand decides to add, and they assume the label figure is DHA as fatty acid, the convention used on the certificate.
| DHA declared | Oil at 35.0% DHA | Oil at 45.0% DHA |
|---|---|---|
| 100 mg | 0.29 g | 0.22 g |
| 200 mg | 0.57 g | 0.44 g |
| 250 mg | 0.71 g | 0.56 g |
| 500 mg | 1.43 g | 1.11 g |
A 500 mg softgel fill therefore carries 175–225 mg of DHA, depending on the lot, and a 1,000 mg fill carries 350–450 mg. That is the practical ceiling of the oil: a declaration above about 450 mg DHA per capsule needs a fill over 1 g, a divided dose or a more concentrated specification. The lot result, not the range midpoint, is what the fill calculation should use, because a 35% lot and a 45% lot differ by 100 mg of DHA in every gram.
What to write into the specification
- “Algal DHA oil, DHA 35.0–45.0% by GC (AOCS Ce 1b-89 or ISO 12966), EPA ≤3.0%, DPA reported.”
- “Free fatty acid ≤0.50% as oleic acid; peroxide value ≤5.0 meq O₂/kg; moisture ≤0.1%.”
- “Source: algal oil from the named strain; not fish oil; fish-free statement on file.”
- “Appearance: clear to slightly hazy oil; no added carrier oil; antioxidants declared if present.”
- “Heavy metals and microbiology as listed; pack and storage condition named.”
- “Target DHA figure and destination market confirmed before the order.”
The CAS number 6217-54-5 belongs beside the DHA line as the marker for the fatty acid, not as an identifier for the oil. The specification also needs the target DHA figure, because “35.0–45.0%” alone leaves the fill weight and the label declaration to be settled after the lot is chosen.
When the oil is the wrong form
A stick pack, a dry blend, a tablet or a clear beverage is a powder project: the oil separates, hazes or floats, and the powder on a carrier gives the formulator a dry ingredient with a declared DHA load. A very high single-capsule dose is also a different project, because the oil's concentration sets how much fill is needed, and the answer may be a divided dose rather than a larger softgel.
The algal DHA oil product page carries the catalog specification. The algal DHA powder page covers the spray-dried alternative, and the oil versus powder comparison takes the carrier and label questions further. The GC methods are in the methods section, and the release workflow is on the quality page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation