Trypsin vs chymotrypsin: two serine proteases, two units
Trypsin and chymotrypsin are both serine proteases found in pancreatic juice, and the practical difference is where they cut. Trypsin cleaves on the carboxyl side of lysine and arginine; chymotrypsin cleaves after aromatic residues such as tyrosine, tryptophan and phenylalanine. Their activity units are defined on different substrates at different wavelengths, so a trypsin figure and a chymotrypsin figure cannot be converted, added or compared. A product that contains both is a blend with two assays, not a stronger trypsin.
A trypsin unit and a chymotrypsin unit are defined by different substrates at different wavelengths, so the two numbers cannot be converted, added or compared.
Two unit definitions, side by side
Both are called USP units, and they measure different events. The trypsin unit is an absorbance change at 253 nm with BAEE as the substrate; the chymotrypsin unit is an absorbance change at 237 nm with ATEE. The conditions differ as well, including the pH.
| Enzyme | EC number | Substrate | Wavelength | Conditions | One unit is |
|---|---|---|---|---|---|
| Trypsin | 3.4.21.4 | BAEE | 253 nm | pH 7.6, 25 °C | A rise of 0.003 absorbance per minute |
| Chymotrypsin | 3.4.21.1 | ATEE | 237 nm | pH 7.0, 25 °C | A change of 0.0075 absorbance per minute |
The chymotrypsin unit is defined on a larger absorbance change, and it is tempting to divide one figure by the other to convert them. That would be wrong. The substrate, the wavelength and the absorptivity of the product all differ, so the two numbers are not on a common scale. A supplier who offers a conversion factor between them is describing a habit, not a definition.
What each assay has to print
A kinetic assay is only reproducible when the reader can repeat it. The certificate should name the substrate and its concentration, the buffer and pH, the temperature, the path length and the reaction volume, and it should report the absorbance change per minute together with the enzyme weight that produced it. The calculation to units per milligram, and the basis on which that milligram was weighed, complete the entry.
The trypsin assay is commonly run in a 3.2 mL reaction in a 1 cm cuvette at 25 °C, and the chymotrypsin assay in a comparable cell at 237 nm. Both need the initial rate rather than an endpoint: a fixed-time reading taken after the reaction has left its linear phase reports a lower rate, and the error is invisible unless the raw trace is requested. Ask for the trace when a result is disputed, not only the final figure.
Why the cleavage site decides the use
Both enzymes carry the same catalytic triad, a histidine, an aspartate and a serine, and the difference sits in the binding pocket that reads the side chain before the cut. Trypsin's pocket holds an acidic residue at its base, which attracts a basic lysine or arginine side chain. Chymotrypsin's pocket is lined with hydrophobic residues and prefers an aromatic side chain, with leucine and methionine accepted more slowly.
The consequence is a different peptide profile from the same protein. A hydrolysate made with trypsin ends more of its peptides at lysine and arginine; one made with chymotrypsin ends them at aromatic residues. For a process that is designed around a peptide size or a functional property, the two enzymes are not interchangeable, and a blend produces a third profile rather than an average of the two.
Both digest themselves, at different rates
Autolysis is the failure mode that the two enzymes share, and it runs fastest near pH 8 for both, which is close to the pH at which they are assayed. A warm, alkaline hold therefore attacks the enzyme that the assay is measuring. Trypsin is stabilised by calcium, so a buffer with a calcium salt holds its activity longer, while a chelator in the same buffer removes the calcium and speeds the loss.
In a two-enzyme product the ratio is the thing to watch. If one enzyme loses activity faster than the other, the blend drifts away from its declared ratio even while each figure stays inside a wide limit. Measure both activities separately at each stability time point; a total protease figure hides exactly the change that matters. Heat, water activity and pH act on both enzymes, and the pack that protects one protects the other.
Ratios belong in units, not in milligrams
Combination products are usually described by an activity ratio, such as equal trypsin and chymotrypsin units, or a multiple in favour of trypsin. The ratio is a ratio of units, and it is not a ratio of masses: each powder carries its own units per milligram, so a 1:1 unit blend weighs different amounts of the two materials. A specification written as “equal parts” has not fixed the ratio that the assay will measure.
The same logic applies inside a trypsin lot. The chymotrypsin that co-purifies is limited as a ratio to the trypsin activity, because a mass percentage would say nothing about how much activity travelled with it. When a certificate gives one figure and no ratio, the reader cannot tell whether the powder is a purified enzyme or a pancreas fraction that happens to pass the trypsin limit.
What the label and the specification must name
If both enzymes are present, both are named, each with its own activity and unit. “Protease” alone hides the identity that the specification has just established, and a single combined figure cannot be checked against either assay. The species and tissue of origin belong on the specification for the same reason: the two enzymes are pancreatic, and the source is part of what the buyer is buying.
A trypsin certificate may carry a chymotrypsin result as a purity limit rather than as an ingredient. That is a different statement from a blend, and the label should make the difference clear: a limit describes what was kept out, a blend describes what was put in. The carrier belongs on the label as well, because a diluted or granulated powder adds a material that the certificate does not describe as an enzyme.
Choosing between them
Start with the bond that has to be cut. A process that needs cleavage at lysine and arginine points to trypsin; one that needs cleavage at aromatic residues points to chymotrypsin. If the process needs both, buy a blend with two assays and two limits rather than a trypsin powder with an unstated chymotrypsin content. If the target is simply “proteolysis”, neither pancreatic enzyme may be the right catalyst, and the neutral and alkaline proteases work at different pH values and carry different units.
The catalog entry is on the trypsin product page; the grades page covers the powder options, the identity page covers the evidence, and the COA page covers the release lines. The neutral protease and alkaline protease entries show how far the unit definitions move between enzymes, the assay vocabulary is in the methods section, and the quality page describes release.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation