03 Stability

Pepsin loses activity to heat and moisture; the pack decides the shelf life

Technical document 03 · Reviewed 2026-11-19 · Pepsin

On this page
  1. The powder: moisture, heat and the pack
  2. The solution: acid keeps it, neutral ends it
  3. What drives degradation
  4. A stability protocol for the ingredient
  5. The finished formula changes the answer
  6. How the shelf life is set

Pepsin is a protein, and its activity falls when the protein unfolds. Heat and moisture drive that loss in the powder; in solution, pH is decisive, because pepsin works in acid and loses activity as the pH rises toward neutral. The retest period comes from stability data on the pack and condition that will actually be used, not from a generic figure attached to the certificate.

In one line

Pepsin is a protein: heat and moisture denature it, acid pH protects it and alkaline pH ends its activity, so the pack and the matrix set the shelf life.

The powder: moisture, heat and the pack

Loss on drying is capped at 8.0% at release. That figure is a gate, not an allowance for storage: the powder is hygroscopic, and an opened pouch in a humid room will move toward the cap. As water rises, the activity per gram of powder as sold falls, even if the enzyme that remains is still intact.

Heat is the second driver. A sealed pack in a normal warehouse is usually acceptable; a loading bay, a vehicle or a greenhouse is not. The loss rate climbs with temperature, so a lot held warm for a season can miss an assay that passed at release.

The pack is part of the specification. The 1 kg foil pouch and the 25 kg fiber drum both depend on a seal and a liner; the drum's liner is the moisture barrier, and a pouch folded over is not resealed. Note the opening date and finish the remainder within the stated in-use period.

The solution: acid keeps it, neutral ends it

Pepsin dissolves in water to give an acidic solution, and the acidity is part of its working condition. The enzyme is active near pH 2 and loses activity as the pH rises; above the acid range, the unfolding becomes irreversible, so a neutral or alkaline solution does not recover when the pH is brought back down.

A solution adds failure modes that a powder does not have: dilution, freeze-thaw, shear and foaming at a pump or stirrer, and autolysis at acid pH and elevated temperature. A concentrated stock holds better than a dilute one, and a clear bottle left on a bench is not where a hold belongs.

If a liquid is unavoidable, keep it acid, keep it cold, limit dissolved oxygen and metal contact, and validate the hold time in the matrix. A result on the bulk powder does not carry over to a beverage.

What drives degradation

Factors that move pepsin activity during storage
FactorWhat it doesControl
HeatUnfolds the protein; activity fallsCool store; short heat exposure in process
MoistureRaises loss on drying; lowers as-is activitySealed pouch; closed drum liner
pHAcid range keeps activity; neutral and alkaline inactivateAcid matrix; check the reconstituted pH
AutolysisPepsin digests itself in acid solutionLow temperature; short hold; concentrated stock
Shear and foamSurface denaturation at pumps and mixersLow-shear transfer; avoid over-mixing
TimeEvery rate above accumulatesAssigned retest period; retained sample

These factors interact. A warm, humid store is worse than either condition alone, and an acid solution held warm combines autolysis with thermal unfolding. The useful question is not whether pepsin is stable in general, but how long it holds in this pack, in this matrix, at this temperature.

A stability protocol for the ingredient

A workable design holds the sealed pack at 25 °C/60% relative humidity for the long term, adds 30 °C/65% relative humidity as an intermediate condition, and uses 40 °C/75% relative humidity to stress the pack. A light arm can be added for transparent pack components, but heat and moisture are the priority here.

At each point, measure activity, loss on drying, appearance, identity and microbiology. For a stick pack or a liquid, repeat the work in the matrix at the process pH and heat load. Report the individual results, not only a pass statement, and identify the pack and the lot family.

Request the summary for the pack you will buy. A drum and a pouch differ in headspace and in how often they are opened, so the data belongs to the pack that generated it.

The finished formula changes the answer

A capsule or tablet has low water activity, but the shell and the excipients can still move moisture into the fill. Measure loss on drying at release and again after storage, and inspect the fill as well as the powder. A stick pack depends on the seal and the foil; a pinhole is a failure, so inspect the strip.

Once the product is dissolved, the blend pH decides. An acidic active such as ascorbic acid or citric acid sits in pepsin's range; an alkaline component can push the local pH above the working window. Measure the pH of the reconstituted product at the start and after storage.

The dosage form decides where the enzyme is released, and that is a formulation choice. An overage is a label and stability decision, and it cannot compensate for a pack that lets moisture in.

How the shelf life is set

We do not publish one shelf-life number for pepsin, because the pack and the storage condition set it. The assigned retest period is written on the specification and backed by the stability file for that pack. A figure quoted without a pack, a condition and a test panel is an assertion, not a shelf life.

At the end of the retest period, re-assay the retained sample before extending use. Do not extend by assumption, and do not apply a bulk figure to a repack. The product hub lists the standard packs; the COA page covers release testing; the MOQ page covers pack and lead time; the quality page describes the release and retained-sample workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation