02 Grade comparison

Pancreatin 1×, a multiple or a dilution: choosing a grade

Technical document 02 · Reviewed 2026-11-19 · Pancreatin

On this page
  1. Why pancreatin comes as more than one grade
  2. The grades side by side
  3. What changes in the drum
  4. What changes in the finished product
  5. What to write into the specification
  6. When a different grade is the wrong choice

Pancreatin is sold as a 1× powder that meets the three USP minima, as a higher-potency multiple labelled 2×, 3× or more, and as a dilution on a declared carrier. The grade changes the mass per serving, the carrier on the label and the dust in the room; it does not change the definition of the three units. The catalog here is the 1× powder.

In one line

The grade is an activity level plus the material that carries it: a 1× powder, a 3× concentrate and a lactose dilution are three different specifications.

Why pancreatin comes as more than one grade

One extract can be presented at different activity levels. The USP monograph allows a higher activity to be labelled as a whole-number multiple of the three minimum activities, so a 3× powder meets at least 75 USP U/mg amylase, 75 USP U/mg protease and 6 USP U/mg lipase. A dilution takes the same extract and adds lactose, sucrose or another declared carrier. Both are legitimate grades; neither is a different enzyme.

The grade decision is a mass-balance decision. The activity target per serving is fixed, so activity per milligram sets the powder weight. That weight has to fit the capsule, disperse in the stick pack or blend without segregating, and remain weighable at production scale.

The grades side by side

Pancreatin grades · what changes in the drum
GradeActivity per mgWhat it isFitsWatch
1× powder, 40 mesh≥25 / ≥25 / ≥2 USP U/mgStandard tissue extractCapsules, tablets, blendsFill weight and the ratio target
Multiple, 2×–6×2–6× the minima, declared as the multipleConcentrated extractHigh target in a small fillDust; the ratio may differ from 1×
DilutionAgreed; the lot still meets the 1× minimaExtract on lactose or sucroseLarge fill or a low targetCarrier allergen and blend uniformity
GranulatedSame as the base powderAgglomerated powderTablets, sachets, low-dust roomsHeat and moisture added by the step

The table is deliberately short. A grade is not a different species, a different unit or a different assay; it is the same extract at a different activity per gram or on a different carrier. An offer that changes the species or the assay is a different material, not a grade.

What changes in the drum

The catalog powder passes 40 mesh, about 425 µm. It is off-white to light tan, soluble in water with a slight turbidity, and carries a glandular odour. The powder raises dust when poured, and enzyme dust is a respiratory sensitiser, so a low-dust grade can matter more to the room than a higher number matters to the formula.

Granulation improves flow and reduces dust, but it adds a binder, water or solvent, a drying step and a milling step. The activity has to be measured after granulation, not assumed from the base powder. A dilution changes the particle-size distribution as well: the carrier may be finer or coarser than the extract, and the two can separate in a blender or hopper. Ask for the particle size of the blend, not only of the enzyme.

A multiple keeps the particle size but raises the activity per scoop, which makes small inclusions harder to weigh accurately and raises the dust load per gram of activity.

What changes in the finished product

The arithmetic is simple and easy to get wrong. A 250 mg fill of 1× powder carries at least 6,250 USP units of amylase, 6,250 of protease and 500 of lipase, because the minima are 25, 25 and 2 U/mg. A 3× powder carries three times that in the same mass. If a formula targets a fixed number of units per serving, the powder weight is the target divided by the activity per milligram.

The fill weight is the constraint. A capsule, a stick pack and a tablet each have a practical mass; a low-activity grade may need more powder than the pack can hold, and a high multiple may need a weigh-up that the plant cannot hit accurately. The carrier appears in the ingredient list, and lactose brings a milk-derived allergen into the label.

For a blend, the grade has to match the other components. A pancreatin at 25/25/2 and a lipase or amylase added separately are weighed in different amounts; changing the pancreatin grade changes the blend ratio and can change the uniformity of the minor components. Specify the units of each activity per serving, not only the mass of pancreatin.

What to write into the specification

  • “Pancreatin 1×, 2×, 3× or the declared multiple, from hog or ox pancreas, CAS 8049-47-6.”
  • “Amylase ≥25, protease ≥25 and lipase ≥2 USP U/mg, multiplied by the declared potency, with the unit definitions and assay conditions.”
  • “Target ratio and tolerance for the three activities, not only three minima.”
  • “Loss on drying ≤5.0%; fat to the monograph limit for the potency.”
  • “Carrier identity and inclusion; particle size ≥95% through 40 mesh.”
  • “Storage in a tight container at not more than 30 °C.”

A line that reads only “pancreatin 25/25/2” leaves the species, the carrier and the ratio open. The specification should be written so that a second laboratory could reproduce the three assays and a second blender could reproduce the blend.

When a different grade is the wrong choice

Do not use a multiple to hit a low target: the weigh-up error grows as the inclusion shrinks. Do not choose a lactose dilution for a label that has to declare no milk. Do not switch grade without recalculating the label and the blend, because the three activities do not scale identically when the extract is standardised. And do not accept a lot whose ratio is wrong because the total activity looks high.

The catalog position is on the pancreatin product page; the release tests are on the COA page; packing and minimum order are on the MOQ page; the lipase page and the amylase page show how a single-activity enzyme differs from a triad.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation