02 Grade comparison

Lumbrokinase grades: activity, carrier and particle form

Technical document 02 · Reviewed 2026-11-19 · Lumbrokinase

On this page
  1. A preparation is not described by a percentage
  2. The catalogue options
  3. Powder, mesh and air quality
  4. The arithmetic behind the choice
  5. Writing the grade into a specification
  6. When another grade is the wrong choice

The catalogue offers one activity grade — a 40 mesh powder at ≥20,000 U/g — plus a granulated version on request. The choice that matters is therefore not “which purity” but which activity, which carrier and which particle form the formula can tolerate. A switch changes the weighed mass, the label and the dust in the room.

In one line

A lumbrokinase grade is an activity plus the material that carries it, so the unit, the protein content and the particle form have to be read together.

A preparation is not described by a percentage

Purity works for a single molecule. Lumbrokinase is a protein mixture extracted from earthworm tissue, and the powder also contains the other soluble proteins from that tissue and any carrier used to bring the activity to a declared figure. Calling the powder “98%” would say almost nothing about how many units it carries or what those units sit on.

The practical description is a set of four facts: activity, protein content, carrier and particle form, with the source species behind them. Two suppliers can use the same product name and differ on every one of those facts. The buyer's job is to compare the facts, not the name — the COA page shows where each one appears on the certificate.

What a lumbrokinase grade decision sets
DecisionWhat it fixesWhere it appears
ActivityUnits delivered per gramDose weight, label, overage
Protein contentProtein load behind the activitySpecific activity, blend behaviour
CarrierWhat the activity is spread onIngredient list, moisture, flow
MeshFlow, dispersion and dustMixing time, uniformity, air quality
Physical formPowder or granuleWetting rate, dust control
SpeciesWhich earthworm material was extractedIdentity file, regulatory dossier

The catalogue options

The standard powder is the reference grade: ≥20,000 U/g, milled to pass 40 mesh, with the carrier stated in the specification. The granulated version is made to order, and a different activity is a new specification rather than a packing variant. Each option has a different effect on the formula, and each needs its own release result.

Lumbrokinase grade options
OptionActivityFormEffect on the formula
Catalogue powder≥20,000 U/g≥95% through 40 meshLowest catalogue dose weight; suited to dry blends
GranulatedAgreed in the specificationGranulesLess dust; slower wetting; activity after granulation
Other activityAgreed in the specificationPowder or granulesNew dose weight, certificate and label basis

Activity figures are comparable only when the method is. A U/g read against one plate standard and a U/g read against another are different measurements, and the difference does not disappear because both sheets use the same letter. The same point applies across products: a nattokinase FU/g is a separate unit system, as the nattokinase specification shows. Neither number can be converted into the other without the method that defined it.

Powder, mesh and air quality

The 40 mesh powder flows well and disperses in water to a clear to slightly turbid solution. The fine fraction is what speeds dispersion and what puts protein into the air when the bag is opened. Enzyme powders are respiratory sensitisers, so the safety data sheet, local exhaust ventilation, closed transfer and a suitable mask are part of the grade decision, not an afterthought for the plant manager.

Granulation reduces dust and slows wetting. A stick pack that must disperse quickly usually takes the powder; a facility that weighs enzyme every day may prefer granules for cleaner air. The granulation step can also reduce activity, so the granulated lot needs a release figure measured after that step. A granulated lot described only by the activity of its parent powder has no result of its own.

The arithmetic behind the choice

The mass required is the declared unit count divided by the activity. For a batch that needs 20,000 U, the weigh-up is 1.0 g of a 20,000 U/g powder, 0.5 g of a 40,000 U/g powder, or 2.0 g of a 10,000 U/g powder. The unit count is identical in all three; the powder mass, the carrier load and the label entry are not. Moving to a two-fold dilution doubles the weight and introduces one part of carrier for every part of enzyme powder.

Weighing accuracy often decides the grade. A small charge is easy in a production batch and difficult in a pilot, where the balance and the mixer both struggle with a few milligrams. A dilution makes the charge weighable, but it carries the carrier into the formula and the ingredient list. The largest batch the formula will run is a better guide than the smallest.

Two rules sit beside the arithmetic. The label has to state whether the declared activity is at release or at the end of the declared shelf life. And a diluted grade is a manufactured lot: its certificate should report the activity of that lot, not the activity of the concentrate behind it. The dosage form then sets the limit. A hard capsule, a stick pack and a tablet each allow a different fill, so fix the form before fixing the grade.

Writing the grade into a specification

  • “Lumbrokinase preparation from earthworm, with the species and tissue named in the source record.”
  • “Activity ≥20,000 U/g by the fibrin-plate method, with plate, standard, incubation and reading rule on the COA.”
  • “Protein content and the method used; specific activity calculated from both.”
  • “Carrier and any additional enzyme activity declared; no undeclared diluent.”
  • “Loss on drying ≤5.0%; ≥95% through 40 mesh; metals and microbiology within the listed limits.”
  • “Label basis: activity at release or at the end of the declared shelf life.”

Write the activity as a minimum, not a target, and keep the method beside it. State the carrier even when none is added; “none” is a declaration, and an unstated carrier is a common reason two quotations at the same activity behave differently. A specification that cannot be tested is not a specification, and a grade that cannot be described in these lines is not ready to quote.

When another grade is the wrong choice

Three objections surface against dilution. Adding maltodextrin cannot help a blend that is already at its carrier ceiling. A carrier that holds water is unwelcome in a formula with a tight moisture budget. And a short ingredient list does not need an entry whose only purpose is to make the powder heavy enough to weigh.

There is also a scale argument: a dilution that solves a pilot weighing problem can become unnecessary once the production batch is big enough for the concentrate to be weighed accurately. Granulation has limits too. A product that must disperse in seconds, or an assay that needs a fully dissolved sample, is better served by the powder. The catalogue values are on the lumbrokinase product page; activity loss after granulation is covered on the stability page; the protein and activity checks are on the methods page and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation