01 COA & batch testing

Reading an invertase COA: activity, unit and release limits

Technical document 01 · Reviewed 2026-11-20 · Invertase

On this page
  1. The certificate as a test report
  2. What the activity number means
  3. Release limit versus batch result
  4. Where the variation comes from
  5. When to order an outside assay
  6. A side-by-side comparison

An invertase certificate is short, and one line carries most of the practical value: the activity. That line is a rate per gram measured on sucrose at a stated pH and temperature, so it is comparable only when the unit definition and the assay conditions are printed beside it. The remaining rows cover appearance, moisture, particle size, metals and microbiology. Read the document as a test report, not as a label.

In one line

The activity is a rate, not a concentration: without the unit definition, the sucrose substrate and the assay conditions, the number cannot be reproduced.

The certificate as a test report

A release certificate is useful when every row can be checked. Each line needs the test, the method and the limit; the measured result belongs in its own column.

Catalog release specification · invertase powder
TestMethodRelease limit
AppearanceVisual inspectionWhite to light tan, free-flowing powder
ActivitySucrose hydrolysis; unit definition stated≥100,000 U/g
IdentificationActivity assay conform; EC 3.2.1.26 and source namedConforms
Loss on dryingGravimetric≤5.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

CAS 9001-57-4 names the enzyme, but it does not identify the preparation. The certificate should also name the production organism and the carrier, because the same activity can be reached by different routes. A specification that stops at CAS and U/g has described a category, not a lot.

What the activity number means

The assay starts with sucrose in buffer. The sample is diluted into the linear range, incubated for a fixed time at a fixed temperature, and the reaction is stopped. Glucose is then measured, usually with glucose oxidase/peroxidase, by a reducing-sugar method, or by HPLC. One molecule of sucrose yields one molecule of glucose and one of fructose, so the glucose result is also the sucrose result. Activity is calculated as micromoles of glucose per minute per gram of powder as sold.

Two published definitions show why the wording matters. One widely used definition sets a unit as the hydrolysis of 1.0 micromole of sucrose per minute at pH 4.5 and 55 °C. The JECFA monograph defines its unit on reducing sugar expressed as invert sugar per minute, and the FCC uses an INVU with its own factor. These are separate definitions; a figure in one is not a figure in another without the method.

What the activity line has to state
ItemRequired detailWhy it matters
Unit basisU per gram of powder as soldA dry-basis or protein-basis figure is a different number
SubstrateSucrose, grade and concentrationThe rate depends on substrate concentration
pHThe assay pHActivity falls outside the working window
TemperatureThe assay temperatureTemperature changes the rate; the assay temperature must be stated
Time and stoppingIncubation time and stop reagentShort or long incubations leave the linear range
DetectionGlucose oxidase/peroxidase, reducing sugar or HPLCDifferent detectors calibrate differently
Calculationµmol glucose/min/g; dilution and blankThe formula is part of the method
Moisture basisAs-is or dry-solids basisWater changes the number without changing the enzyme

The commercial basis is per gram of powder as sold. A carrier dilution lowers the units per gram without changing the enzyme; a dry-solids figure can look higher because it removes water.

Release limit versus batch result

≥100,000 U/g is a floor, not a target. Two lots at 104,000 and 210,000 U/g would both pass, yet a process that consumes part of the activity would respond to them differently. The limit is the gate; the measured value is what the formulator has to work with.

What the batch result should show
TestRelease limitWhat the lot result shows
Activity≥100,000 U/gMeasured U/g, with method, unit definition and RSD
Loss on drying≤5.0%A measured percentage
Heavy metalsPer elementOne figure per element, in mg/kg
MicrobiologyCounts and absenceThe plate count plus the absence result
Particle size≥95% through 80 meshThe percentage that passed the 80 mesh sieve

Ask for the method reference, the release date, and whether the value refers to release or to the end of the shelf life.

Where the variation comes from

Fermentation is the first source of spread. Strain, medium, sucrose feed, aeration and harvest time change how much enzyme the cells make. Recovery and concentration decide how much of that activity reaches the powder. Standardisation with a food-grade carrier then fixes the units per gram, and drying and milling can lose activity through heat.

Water and heat continue to move the figure after release. A powder stored in a humid room picks up moisture, and the as-is activity falls even when the protein is intact. Colour is not a release test: a darker tan can follow a longer dry while the activity remains in specification. Read the batch record before rejecting a lot on appearance.

Method drift is harder to see. A new substrate lot, a recalibrated glucose standard or a different incubation bath can make two U/g results incomparable even when the paperwork looks identical.

When to order an outside assay

An outside assay earns its place for a new source, an initial shipment to a regulated market, a disputed result, or a label statement that rests on the activity figure. The scope can remain modest: the named activity method on a retained sample, protein or specific activity, moisture, the metal panel, microbiology, and a protein pattern compared with a reference preparation.

The laboratory has to use the same substrate, pH, temperature and calculation as the specification; otherwise the exercise compares methods, not powders. A report in SU/g is not a second opinion on a U/g result unless the SU definition is the same. The sample and the report must carry the same lot code, and the report should state the laboratory's accreditation for each test.

A side-by-side comparison

Put six lines side by side: the unit and its definition, the assay pH and temperature, the measured activity, the protein figure or specific activity, the moisture and the mesh, and the source organism with its carrier. Agreement on U/g is not agreement on the preparation; the other five lines decide that, and a trial will expose the gap before the quotation does.

Traceability comes next. The lot code on the paper must match the pouch and the retained sample, and the certificate should name the source organism. If the code does not match the pack, the certificate is valid for some other delivery.

The catalog values sit on the invertase product page. The checks that separate a real preparation from a diluted or substituted one are on the identity page; the quality page sets out how a lot is released; the assay families are compared in the methods library; the terms are defined in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation