01 COA & batch testing

What the COA for glucose oxidase actually contains

Technical document 01 · Reviewed 2026-11-20 · Glucose Oxidase

On this page
  1. Reading the certificate line by line
  2. One unit, and the conditions behind it
  3. The limit, the result and the evidence
  4. What moves between batches
  5. When an outside laboratory is justified
  6. What to compare between suppliers

The certificate for a glucose oxidase lot reports activity, the conditions that define the unit, identity, loss on drying, heavy metals, microbiology and particle size. Activity is the line that needs the most context: the catalog figure comes from a peroxidase-coupled glucose assay, and the same powder reads differently at another pH, temperature or detection system. The first table is the catalog specification; the lot certificate is the evidence for a particular pack.

In one line

A glucose oxidase figure is a rate from a coupled assay: the unit, the pH, the temperature and the peroxidase detection system have to travel with the number.

Reading the certificate line by line

Each line should stand on its own: the measurement, the method and the release limit. A row that says only “conforms” asks for trust without the evidence.

There is no simple colour reaction or melting point that identifies the enzyme, so the identity line is the activity assay itself. CAS 9001-37-0 and EC 1.1.3.4 identify the enzyme, not the preparation in the drum; the certificate should also name the production organism, the carrier and the lot.

Catalog release specification · glucose oxidase
ParameterMethodRelease limit
AppearanceVisualYellow to light tan, free-flowing powder
Glucose oxidase activityPeroxidase-coupled glucose assay≥10,000 U/g
IdentificationActivity assayConforms to the reference
Loss on dryingGravimetric≤8.0%
Particle sizeSieve analysis≥95% through 80 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyEnumeration and absence checksAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

An activity figure is a rate, so the method column is part of the result, not a footnote. The mesh is a finishing specification, and it can change when the mill changes without any change in the enzyme.

One unit, and the conditions behind it

One unit is the amount of enzyme that oxidises one micromole of β-D-glucose per minute under the conditions of the method. The catalog method is a glucose/peroxidase assay: glucose oxidase produces hydrogen peroxide, peroxidase uses it to oxidise a chromogen, and the laboratory follows the colour. The specification can be agreed at pH 5.1 and 25 °C, which is the common definition, but the certificate has to print the values it actually used, because a rate at 30 °C is not the rate at 25 °C.

The coupling adds its own conditions. The glucose concentration must be high enough to keep the enzyme saturated, the peroxidase must not be limiting, and the chromogen sets the wavelength. A laboratory that changes the chromogen has changed the method. Glucose oxidase acts on the β-anomer of glucose, so the assay also depends on mutarotation; a reading taken before the anomers equilibrate can be low.

Activity is reported per gram of powder as sold. If a lot reads 10,000 U/g as-is with 8.0% loss on drying, the dry-basis figure is 10,870 U/g; both describe the same powder, and anyone comparing them is comparing denominators. A specific activity figure, U per milligram of protein, belongs on a separate line and needs a named protein method.

The limit, the result and the evidence

A release limit marks the boundary; the batch result records what the laboratory found. They need separate columns, with the method beside them. If the result column repeats the specification, it reports the gate, not the measurement.

How a batch result should be reported
ParameterRelease limitExpected result
Activity≥10,000 U/gThe measured U/g, with conditions and moisture basis
IdentificationActivity assay conformsThe activity result, with the method
Loss on drying≤8.0%The measured percentage for the lot
Heavy metalsPer elementEach metal reported separately in mg/kg
MicrobiologyCounts and absenceThe count and the absence result

The limit is a floor, not a target. A lot at 10,500 U/g and one at 24,000 U/g both clear it, yet they will not behave the same after a hot blend or a week in solution. The measured value shows how much margin the lot carries. Ask for the assay's repeatability too; a result just above the floor is a thin cushion if the method varies by several per cent.

Identification by activity is a conclusion drawn from the same number; if the result is disputed, the protein pattern and the preparation description are the next layer.

What moves between batches

Fermentation and recovery decide the protein mixture; standardisation then adjusts the final powder to a target activity with a declared carrier. Two concentrates of different strength can therefore leave the plant at the same U/g. The practice is routine, but only if the carrier is on the specification and the assay is run after standardisation, not before.

The dryer and the mill are the next variables. Heat in either step can strip activity while the lot still clears the release limit; moisture shifts the as-is figure but not the enzyme itself. Colour is the least quantitative line: a tan shift can follow a longer dry or a different carrier, and it is not proof of damage.

Read the direction across several lots rather than one result at the limit: the assay drifting low, moisture creeping up, or an extra protein band are more informative than a single pass. Certificate, pouch, drum and retain should share a lot code.

When an outside laboratory is justified

An outside test is worth ordering for an unfamiliar source, a first delivery to a regulated market, a disputed activity figure, or a label value that rests on the result. The useful panel is limited: activity on the retain by the named method, protein and specific activity, moisture, ICP-MS metals, microbiology, and a catalase check if peroxide accumulation matters.

The laboratory has to match the specification's pH, temperature, glucose concentration and detection system; otherwise the comparison is between methods, not powders. Ask for the limit of detection behind each screen and the accreditation scope behind the activity method. “Not detected” is a statement about the method unless a limit is given.

Traceability decides whether the test has weight: the sample should be the retain, the report should quote the lot code, and a referee should receive the retain and the specification. Repeating the same assay adds a number, not an answer; the useful second test separates inactive enzyme from a diluted powder.

What to compare between suppliers

Put six rows side by side: source organism and CAS number; activity and its full unit definition; protein or specific activity; moisture and carrier; metals and microbiology; pack, lot and storage. Two offers that agree on U/g but differ on pH or detection are not the same powder.

The second layer is traceability: who made the lot, from which organism and with which carrier. Catalog values are on the glucose oxidase product page. The tests are on the identity page, the grade options on the grades page, the assay logic in the methods library, and the release workflow on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation