01 COA & batch testing

What the COA for cellulase actually contains

Technical document 01 · Reviewed 2026-11-19 · Cellulase

On this page
  1. The certificate as a test report
  2. What the CU/g figure measures
  3. Release limit versus batch result
  4. What moves between batches
  5. When an outside laboratory earns its fee
  6. What to compare between suppliers

The certificate for a cellulase lot reports appearance, activity in CU/g, the pH of a 1% solution, loss on drying, particle size, the heavy-metal panel and microbiology. The activity row is the only line that describes the enzyme, and it means little unless the certificate sets the unit definition, the substrate and the conditions beside it. The ranges here are the catalog specification; the batch COA is the document that confirms one drum of cellulase powder.

In one line

A cellulase activity figure is a rate measured under one assay, so the certificate has to carry the unit, the substrate and the conditions next to the CU/g.

The certificate as a test report

A certificate can be audited only if every row carries what was measured, the method behind the number, and the limit the lot was released against. For an enzyme the activity row needs a fourth element, the assay conditions.

Release specification · cellulase powder from Aspergillus niger
ParameterMethodRelease limit
AppearanceVisualOff-white to light tan, free-flowing powder
Cellulase activityReducing-sugar assay on carboxymethyl cellulose, CU/g≥50,000 CU/g
pH (1% solution)Potentiometry4.5–5.5
Loss on dryingGravimetric≤8.0%
Particle sizeSieve analysis≥95% through 40 mesh
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤10,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
The activity row, read line by line
ElementWhat it has to sayWhy it changes the figure
UnitCU per gram of powder as soldPer gram of preparation, not per gram of protein
SubstrateCarboxymethyl cellulose, or filter paperSoluble CMC reads endo action only
TemperatureUsually 50 °CA rate at one temperature does not describe another
pH4.5, 4.8 or 5.0, per the house methodThe same powder reads lower at pH 3
DetectionDNS colour against glucose, or fluidityTwo principles, two scales
BasisAs-is, or corrected to dry solidsMoisture moves the number at unchanged activity

What the CU/g figure measures

A unit of cellulase is a rate, not a weight and not a purity. One CU is defined by the assay that produces it: either the amount of enzyme that liberates a set quantity of reducing sugar from carboxymethyl cellulose per minute as glucose equivalents, or the amount that produces a defined change in the fluidity of a CMC solution in five minutes at 50 °C and pH 4.5. Both definitions are in trade use, and the certificate has to say which one it follows.

The substrate decides what is counted. Carboxymethyl cellulose is soluble, so a CMC assay reads endo-1,4-β-glucanase action and largely ignores the cellobiohydrolase and β-glucosidase in the same broth. A preparation can carry a high CU/g and a modest action on insoluble cellulose, or the reverse. The note on CU, EGU and FPU separates the scales.

The reading comes from dinitrosalicylic acid colour at about 540 nm, converted through a glucose standard curve and divided by incubation time and enzyme charge; each of those steps is somewhere two laboratories can diverge. Protein by a colorimetric assay against a bovine serum albumin standard gives the second useful number: units per milligram of protein separates a concentrated preparation from one extended with carrier.

Release limit versus batch result

Activity is a one-sided limit: a lot at 52,000 CU/g and a lot at 78,000 CU/g both pass ≥50,000 CU/g. The release result, not the limit, tells a formulator how much headroom the powder carries into a process step that will consume part of it.

A result column that repeats the specification is not a result, and the word "conforms" is a conclusion the reader should be able to reach from the numbers. Ask for the measured value, the method reference and the release date on the same page. Activity also falls in storage, so the certificate should state the release date, the storage conditions assumed and the activity guaranteed at the end of the declared shelf life. A drum received six months after release is bought at the lower figure.

Request the assay's repeatability as well: with a wide relative standard deviation, a result a few percent above the limit is a coin toss on retest.

What moves between batches

The fermentation sets the starting point: strain, medium, induction and harvest shift the balance of enzymes in the broth. Recovery and ultrafiltration decide how much of that balance reaches the concentrate, and standardisation with a carrier sets the final activity per gram. A supplier holding ≥50,000 CU/g is choosing where in the concentrate to land, so the spread between lots is a process decision as much as a biological one.

Moisture, pH and particle size move with drying and milling and move the activity figure with them: a wetter powder reads lower per gram at constant true activity, and a milling step that generates heat can destroy activity before the sieve is reached. Colour is the least quantitative signal and often the most revealing: a darker tan can follow a hotter dry or a longer hold while the assay still passes, so read the batch record before rejecting a lot on colour.

Watch the method as closely as the number: if substrate grade, buffer or incubation time changes between lots, two certificates that both say CU/g are not comparable.

When an outside laboratory earns its fee

An independent test is worth ordering for a new source, a first shipment into a regulated market, a label claim that rests on the activity figure, or a disputed result. The panel is narrow: activity by the buyer's own CU method on a retained sample, protein, loss on drying, heavy metals by ICP-MS, microbiology and a protein pattern by gel electrophoresis.

The referee has to run the same substrate and conditions as the specification, or the comparison measures methods rather than powder. Ask for the detection limit on each metal; a "not detected" line without a limit describes the method, not the sample. The sample tested should be the sample retained, with the lot code on both.

What to compare between suppliers

Put six lines side by side: unit definition, substrate, assay conditions, activity result with method, protein and specific activity, moisture and particle size. Two quotations that agree on CU/g but differ on the other five are not describing the same preparation, and the gap surfaces at the first process trial.

Traceability is the second layer. The lot code should be identical on the certificate, the pack and the retained sample, and the certificate should name the production organism and strain, because the source is part of a food enzyme's identity. A correct certificate can still belong to a different lot than the one on the loading dock.

The catalog numbers sit on the cellulase product page, the tests that separate a genuine lot from a diluted one are on the identity page, the release workflow behind the certificate is on the quality page, and the vocabulary is in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation