03 Stability

Cellulase activity falls with heat and moisture; the process decides the shelf life

Technical document 03 · Reviewed 2026-11-19 · Cellulase

On this page
  1. The powder in its sealed pack
  2. Once the powder is dissolved
  3. What actually destroys activity
  4. A stability protocol that answers the question
  5. The blend is part of the stability
  6. Assigning a shelf life

Dry cellulase powder loses activity slowly; the loss accelerates with moisture, with heat, and with a pH away from the 4.5–5.5 window the powder is made for. The step that puts the enzyme into the product — wet granulation, a heated dry, a tablet press — usually removes more activity than the storage that follows. That is why a shelf life belongs to a process and a pack, not to a powder on its own.

In one line

A sealed pack holds the activity; the wet step, the heat and the water activity of the finished blend decide how far it has fallen by the end of shelf life.

The powder in its sealed pack

At low water activity the enzyme is close to inert. The protein is dry, molecular motion is limited, and the reactions that destroy activity need water. A foil pouch or a lined drum at ambient temperature therefore holds the declared activity for a long time, and the loss over months is small compared with what a single wet process step can remove in an hour.

Two habits protect that state. The first is to keep the pack closed until the batch is ready: the powder is hygroscopic, and an open pouch in a humid room picks up water quickly. The second is to read the loss-on-drying result as a release gate rather than a storage specification. The catalog limit is ≤8.0% and the loss-on-drying note explains what the figure does and does not say about the water that matters.

Once the powder is dissolved

Dissolved, the enzyme is a protein in water with its native structure exposed, and the loss of activity is fast enough to be a formulation problem rather than a storage footnote. Temperature, pH and time set the rate; a solution held warm for a shift can lose a noticeable share of its activity before the filling line is reached.

Microbial growth in a wet system adds a second route to loss, because contaminating organisms release proteases that cut the enzyme. A liquid blend is therefore a stability question rather than an arithmetic one: the number comes from a study on the actual preparation.

Pasteurisation and hot fill are the hard cases. Cellulase from Aspergillus niger works at an optimum near 50 °C and unfolds above roughly 60 °C, so a heat step of minutes at 70–90 °C removes a large share of the activity, and the loss is not recovered on cooling. If the process needs that heat, the activity has to be dosed for the far side of it.

What actually destroys activity

Loss routes and the control that answers each one
FactorWhat happensControl
Heat above about 60 °CProtein unfolds; the loss is irreversibleDose after the hot step, or overage for it
Moisture in the blendWater restores mobility; hydrolysis and oxidation resumeKeep water activity low; dry the granule
pH below 4 or above 7Structure changes away from the working windowBuffer the wet blend near pH 4.5–5.5
Wet granulationWater plus binder plus drying heat in one stepLow-water binder, short low-temperature dry
Tablet compressionLocal heat and shear at the punchDirect compression; check activity in the tablet
Trace metalsIron and copper catalyse oxidation of the proteinSource the mineral salts; test the blend
Opening the packHumid air enters the headspaceReseal, desiccant, small packs for samples

A stability protocol that answers the question

Three production lots, one assay method, and time points at 0, 1, 3, 6, 12 and 24 months at 25 °C and 60% relative humidity. Add a second condition at 30 °C and 65% relative humidity, or at 30 °C and 75% for a tropical market, plus a six-month accelerated run at 40 °C and 75%. Test activity, loss on drying, appearance and microbiology at every point.

Run the study on the material the customer receives, in the pack the customer receives. A study on the concentrate in a laboratory jar says little about a diluted grade in a foil stick, because the carrier, the headspace and the fill weight have all changed. Where a process step is planned, run a sample of the blend before and after that step as well, so the process loss is measured rather than assumed.

Report the result as a percentage of the initial activity, not only as an absolute figure. A lot that starts at 60,000 CU/g and ends at 51,000 CU/g has lost 15%, and the absolute number hides whether the drop came from the material or from the starting point.

The blend is part of the stability

Neighbours matter. An acidic fruit powder lowers the local pH as soon as any water is present, and a wet blend that sits at pH 3.2 for an hour is outside the window the enzyme was made for. Ascorbic acid with a trace of iron or copper generates oxidants that attack the protein. Mineral salts can inhibit or catalyse depending on the metal, and a reducing sugar in a heated wet granulation gives colour and holds water in the granule.

The process choice follows from that. Direct compression and dry blending are gentler: no water is added and no drying heat is applied. If the formula needs granules, the binder should be low in water, the dry short and the temperature low, and the activity of the granule should be measured rather than calculated from the powder. The custom processing page sets out how a process trial is scoped.

Packaging closes the loop. A foil laminate with a good seal, a desiccant where the climate demands it, and a fill weight that leaves little headspace all slow the loss. A stick pack is not a drum: the surface-to-mass ratio is far higher, and the pack is opened once and used at once.

Assigning a shelf life

A shelf life is assigned from the study on the actual pack, not from a general statement about enzyme powders. Take the time at which activity stays above the declared end-of-shelf-life figure, subtract a margin for the assay and the lot-to-lot spread, and write the storage conditions beside it.

One lot is not a shelf life. Three lots show the batch-to-batch spread, and a single lot can be an unusually good one. If the label claim is "not less than 50,000 CU/g at end of shelf life", the release specification needs headroom above that figure to cover the loss and the spread, and the stability data sets the size.

The storage statement belongs on the pack and on the certificate: keep dry, keep closed, and avoid heat above the working window. The commercial terms around the shelf life — how much of it must remain at delivery — are set out on the MOQ and ordering page, the release workflow is on the quality page, and the catalog figures are on the cellulase product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation