06 Identity & adulteration

How we prove a beta-glucanase lot has the declared activity

Technical document 06 · Reviewed 2026-11-20 · Beta-Glucanase

On this page
  1. Four questions, four kinds of evidence
  2. The ratios that separate a preparation from a dilution
  3. X-ray diffraction and the limits of a solid-state test
  4. How a substituted lot presents
  5. Identity clauses for the specification
  6. Five questions to put in writing

A beta-glucanase lot is identified by four agreeing lines: the document names the enzyme, its EC number and its source; the activity assay on a beta-glucan substrate matches the specification; the protein figure is consistent with the declared specific activity; and the lot code ties the certificate to the pack. The activity figure alone cannot separate beta-glucanase from a cellulase or from a diluted lot.

In one line

Identity rests on three agreeing lines — source, glucan assay and protein — and on a lot code that links them to the pack.

Four questions, four kinds of evidence

A certificate may name the correct material without proving it. The four rows below ask separate questions, and each needs its own evidence. An answer to the first question alone describes a document, not a drum.

Four layers of beta-glucanase identity
LayerQuestionEvidenceWhat it proves
DocumentAre the enzyme and source named?Name, EC 3.2.1.6, CAS 9025-70-1, strainPaperwork only
ActivityDoes it cut the beta-glucan substrate?U/g assay on a beta-glucan substrateThe function, not the source
ProteinIs the activity on a plausible protein load?Protein and specific activity, U/mgConcentration versus dilution
TraceabilityDoes the certificate belong to this pack?Lot code on pack, certificate and retainThe link between paper and powder

The first layer is the preparation itself: the enzyme name, EC 3.2.1.6, CAS 9025-70-1, the production organism and strain, the carrier and the 80 mesh. The catalog identification line is the activity assay, so the second layer carries most of the weight. That is normal for an enzyme preparation, and it is also why a single assay is not enough.

The ratios that separate a preparation from a dilution

Protein is usually read by a colorimetric method calibrated with bovine serum albumin. Divide the activity by the protein to get specific activity, U/mg. That figure separates a concentrate from a diluted powder, since dilution pulls both numbers down and leaves the ratio intact. A ratio that falls while U/g holds steady means extra protein per unit of activity: more carrier, a different recovery cut or an inactive fraction.

The second ratio is the substrate pair: activity on beta-glucan against activity on carboxymethyl cellulose. A genuine beta-glucanase preparation is expected to be high on the glucan and lower on CMC; a cellulase preparation usually reads higher on CMC than on the glucan assay. The pair is evidence, not a fixed conversion, because the absolute figures depend on each method. Run both assays on the same sample when the identity is in question.

X-ray diffraction and the limits of a solid-state test

Enzyme powders are amorphous. Their X-ray pattern is a broad halo rather than sharp reflections, so XRD cannot distinguish beta-glucanase from another enzyme preparation, confirm the source, or measure activity. In a commercial powder, sharp peaks usually come from a crystalline carrier or a mineral contaminant; the enzyme itself is not crystalline.

XRD remains useful for two narrow questions: whether the carrier is crystalline, and whether an inorganic contaminant is present. It is not a release test here, and a line saying “XRD conforms” with no pattern or reference adds little. Identity evidence comes from the glucan assay, the protein figure and a protein pattern against a reference lot.

How a substituted lot presents

How a beta-glucanase lot can be substituted, and what shows it
MismatchHow it presentsEvidenceTest
Carrier dilutionNormal powder, lower U/g than the labelActivity and protein both lowActivity plus protein
Cellulase substitutionPlausible glucanase activity, different specificityHigh CMC activity relative to glucanBoth assays, protein pattern
Xylanase substitutionAnother hemicellulase in the drumNo glucan activity, or a weak oneGlucan assay, protein pattern
Added reducing sugarAssay reads high without more enzymeHigh activity, normal proteinBlank, sugar screen, specific activity
Heat-inactivated powderCorrect appearance, low activityActivity low at every dilutionActivity after two hold times
Carrier swap without noticeThe written specification is unchangedFlow, water or mesh movesCarrier identity, change control
Wrong labelCertificate names a different drumLot codes disagreePack, COA and retain

Dilution and added reducing sugar work against each other: the first pushes activity down, the second pushes the reading up. Test activity and protein on one sample, and the pair shows which effect is in play. A powder at 50,000 U/g with 2% protein and another at 50,000 U/g with 10% protein are different materials.

Identity clauses for the specification

  • “Beta-glucanase, EC 3.2.1.6, CAS 9025-70-1, with the production organism and strain named.”
  • “Activity ≥50,000 U/g by the beta-glucan substrate assay; state substrate, pH, temperature and detection.”
  • “Protein and specific activity reported; the method and the standard named.”
  • “Loss on drying ≤8.0%; particle size ≥95% through 80 mesh.”
  • “Carrier identity, declared activity basis and storage statement on the specification.”
  • “Side activity on carboxymethyl cellulose reported when the application depends on specificity.”

Five questions to put in writing

  1. Name the organism and strain behind this lot, and attach the strain statement.
  2. Define one unit: substrate, pH, temperature and how the signal is read.
  3. Report U/g and protein for the lot, then divide them to give U/mg.
  4. Run the carboxymethyl cellulose assay beside the glucan assay and report both.
  5. Which document ties this lot code to the pack?

Written answers to all five give a buyer material to audit. An answer to the third alone gives a number that is easy to produce and difficult to verify. The catalog figures are on the beta-glucanase product page; the certificate lines are on the COA page; the unit comparison is on the beta-glucanase vs cellulase page; the assay formats are in the methods library; and the release sequence is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation