What the COA for L-tyrosine actually contains
The certificate for an L-tyrosine lot reports appearance, infrared identification, the ninhydrin reaction, assay by HPLC on the dried basis, specific rotation, loss on drying, residue on ignition, pH, particle size, the heavy-metal panel and microbiology. Each line needs a method and the release limit; the ranges here are the catalog specification, and the batch COA confirms one drum.
The assay says how much tyrosine is in the sample; the rotation says it is the L form, and the dried basis says what the percentage measures.
Reading the certificate line by line
Read the sheet line by line: each row should name what was measured, how, and against which limit.
| Parameter | Method | Release limit |
|---|---|---|
| Appearance | Visual | White crystalline powder |
| Identification | Infrared absorption | Conforms to reference spectrum |
| Identification | Ninhydrin reaction | Conforms; free α-amino acid |
| Assay (dried basis) | HPLC | 99.0–101.0% |
| Specific rotation | Polarimetry, 1 N HCl | −11.0° to −12.3° (dried basis) |
| Loss on drying | Gravimetric | ≤0.5% |
| Residue on ignition | Gravimetric, ashed | ≤0.1% |
| pH (saturated solution) | Potentiometry | 5.0–7.0 |
| Parameter | Method | Release limit |
|---|---|---|
| Particle size | Sieve analysis | ≥95% through 40 mesh |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The first table identifies the substance; the second the powder. A certificate with an assay and no rotation has counted the material but not identified it.
HPLC, the dried basis and the rotation
The assay is an HPLC result. The phenol group of tyrosine absorbs in the ultraviolet, so a reverse-phase method with UV detection is the usual route. A reproducible method note lists the column, the mobile phase, the standard and the calculation. A percentage without them is a claim, not a measurement.
The dried basis removes the water from the denominator. Divide the result by the dry matter and the figure rises; at ≤0.5% water the lift can reach half a point, enough to cross the 99.0% line. The 101.0% ceiling is there for the standard's response and the method's variation, not because the molecule can exceed 100% purity.
Loss on drying covers water and volatiles, and residue on ignition covers the inorganic ash. Neither is a purity figure, and the assay is not simply 100% minus those lines: an impurity that does not absorb at the detection wavelength can sit in the sample without moving the main peak. Where the risk assessment needs that coverage, add a related-substance test rather than infer purity from the assay.
The specific rotation is measured on the dried material in 1 N hydrochloric acid, so the certificate should state the concentration, the temperature and the path length beside the figure. The window of −11.0° to −12.3° is the optical signature of the L configuration; a racemate or a salt will not sit inside it by accident, but rotation narrows the field rather than naming the amino acid. The pH is taken on a saturated solution: a figure outside 5.0–7.0 points to acid or alkali carried over from crystallisation, or to a different salt.
Release limit versus batch result
The release limit is the gate; the batch result is the measurement. They belong in separate columns, with the method beside both. A column filled with the specification range is a copy of the gate, not a measurement.
| Line | Release gate | Batch result on the certificate |
|---|---|---|
| Assay | 99.0–101.0% on the dried basis | One lot figure, with method and drying basis |
| Specific rotation | −11.0° to −12.3° on the dried basis | One lot figure, with solvent and conditions |
| Loss on drying | ≤0.5% | One figure; no lower bound |
| Heavy metals | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg | Four figures, one per metal |
The two-sided lines — assay, rotation, pH — need a figure that can be read against both ends of the range. The one-sided lines — loss on drying, residue, the metals — pass anywhere below the limit. “Passes specification” is a conclusion, not a measurement.
What moves between batches
Moisture is the variable that moves first. The dryer's end-point, the packing-room air and the state of the liner all land in the loss-on-drying figure, and the dried-basis assay follows. A lot can pass the assay window while carrying more water than the last one, which appears as caking and poor flow before it appears as a rejection.
Rotation is more stable, which makes a real shift easier to see. A change of a degree inside the window deserves a look, because rotation is the only release line that tracks the enantiomeric ratio. D-tyrosine drags the reading toward zero; a small amount can remain inside the gate, which is why rotation is a screen and not an enantiomeric purity grade.
pH and particle size are the practical variables. A shortened wash leaves acid or alkali and moves the pH; a change in milling moves the 40-mesh fraction and the flow. Colour is less quantitative and often more revealing: a cream or tan tint can point to a hot drying step or a trace of metal while the assay passes, so ask for the batch record before rejecting on colour.
When to order an outside test
A new source, a first regulated-market shipment, a rotation close to the limit, or a disputed result are the usual reasons to go outside. The panel can be narrow: rotation on a fresh solution, chiral HPLC for D-tyrosine, IR, loss on drying, ICP-MS and a plate count.
Give the referee laboratory a defined brief: rotation on a freshly prepared solution, a chiral HPLC result for the D enantiomer, and the detection limit that result was measured against. A “not found” result is only as useful as its limit. If the numbers disagree, test the retained sample and trace the lot code across the certificate, the pack and the referee's report.
What to compare between suppliers
A useful comparison puts six lines together: the declared name and form; the assay with its method and basis; the rotation with its conditions; loss on drying; pH and particle size; and the contaminant and micro panels. If two suppliers match on the assay but sit at opposite ends of the rotation window, the powders are not the same material.
Traceability is the next layer. The lot code on the certificate, the pack and the retained sample should be one string, and both the manufacturing site and the pack date belong on the certificate.
The catalog specification sits on the L-tyrosine product page. The forms are set side by side on the grade page; the case that separates the L form from a racemate is on the identity page; the release workflow is on the quality page. The separation is explained in the HPLC method note, and loss on drying is defined in the glossary.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation