06 Identity & adulteration

How we prove an L-histidine lot is the free base

Technical document 06 · Reviewed 2026-11-19 · L-Histidine

On this page
  1. The five identity layers
  2. Chloride, water and the salt ratio
  3. XRD and the crystalline solid
  4. The adulterants that fit the assay
  5. How to write the identity block
  6. Five questions for the supplier

Identity for L-histidine is proven in layers, not by one number. The document set ties the lot to a specification; IR establishes the functional groups; HPLC confirms the retention and the peak; the specific rotation establishes the L configuration; and pH, chloride, water and the assay establish whether the powder is the free base or a salt. The layers have to agree. A clean assay with no rotation has not shown the L form, and a rotation with no pH or chloride has not shown the free base.

In one line

Identity is a set of agreeing measurements: IR and HPLC name the molecule, rotation fixes the L form, and pH with chloride separates the free base from the salt.

The five identity layers

A certificate can name the right material and still fail to prove it. Each layer below answers a separate question and needs its own evidence; a supplier who answers only the first has described the paperwork.

What each identity layer proves and misses
LayerTestWhat it provesWhat it misses
DocumentSpecification, COA, lot codeThe lot is described and traceableWhether the drum matches the paper
SpectrumIR against a reference; HPLC retentionThe functional groups and the chromatographic peakPurity, and a close analogue
ChiralSpecific rotation; chiral HPLCThe L configuration, and a gross excess of the D formA small enantiomeric impurity inside the method's uncertainty
FormpH, chloride, waterFree base or hydrochlorideWhich hydrate, without the water line
QuantitativeAssay, loss on drying, related substancesHow much histidine is present, and what dilutes itA non-chromophoric organic at low level

The layers are not interchangeable: IR can match while the rotation is low, and the assay can pass while the pH says hydrochloride. A useful certificate carries all five.

Chloride, water and the salt ratio

The free base and the hydrochloride differ by a counter-ion and, in the commercial salt, one molecule of water. The monohydrate is C6H9N3O2·HCl·H2O at 209.63 g/mol: about 74.0% histidine, 16.9% chloride and 8.6% water by theory. The ratio is stoichiometric, so it does not move with the assay. The free-base monograph limits chloride to 0.05%, which is the other end of the same scale.

That ratio is a direct form check: a lot sold as the free base with 16% chloride is the salt, whatever the assay says, and a hydrochloride with low chloride and low water is a blend or a different hydrate. A blend lands between the endpoints in proportion to the salt fraction, and the pH moves with it: the free base sits at 7.0–9.0 in a 1% solution, the hydrochloride at 3.0–5.0 in a 5% solution.

The water line also names the hydrate. The anhydrous hydrochloride, CAS 645-35-2 at 191.62 g/mol, carries no water of crystallisation and delivers about 81.0% histidine. A specification that says only “hydrochloride” leaves an 8.6% mass difference open, enough to change a dose; report water or loss on drying, and name the hydrate.

XRD and the crystalline solid

X-ray diffraction asks a different question: is the solid crystalline, which pattern is present, and does it match a reference? It can distinguish a crystalline salt from an amorphous dilution, and it can compare lots from two sources. It is not a purity assay and it does not measure the counter-ion. Ask for the reference pattern and the detection limit before reading a “match” statement.

L-histidine is polymorphic: the literature describes at least two forms, A and B, and the crystallization route decides which appears. A polymorph change can alter dissolution, flow and tablet behaviour without changing the assay. If a supplier claims a specific solid form, XRD answers the question.

For a disputed lot, XRD plus chloride plus HPLC is stronger than any one of them. XRD is not a routine release test, and a certificate that reports only “XRD conforms” without the pattern has added little. It is most useful when the question is the solid form rather than the amount.

The adulterants that fit the assay

Common substitutions and the lines that catch them
AdulterantWhy it can pass a rough checkWhat catches it
L-histidine hydrochlorideContains histidine; the mass is higher per unit of histidinepH; chloride; water; IR
D-histidine or a racemateSame formula and mass; same assaySpecific rotation; chiral HPLC
Other amino acidsSimilar acid–base behaviour and ninhydrin responseHPLC profile; rotation; IR
HistamineClose structure; one decarboxylation step awayLC-MS/MS or a specific related-substances method
WaterCorrected out of a dried-basis assayLoss on drying; as-is calculation
Mineral diluentAdds mass without contributing to the peakResidue on ignition; chloride; mass balance

The hydrochloride is the most plausible substitution because it is a legitimate material with a legitimate certificate. Residue on ignition does not catch it: the chloride is lost on ignition, and the ash can stay low. pH and chloride separate the salt from the base, so a chloride line belongs in the specification even though the catalog certificate does not carry one.

Other amino acids are caught by the chromatogram, not the percentage; proline is a useful system-suitability marker, and glycine is a common diluent. Water is the simplest diluent: a wet lot can pass a dried-basis assay while the as-is powder contains less histidine, so read loss on drying with the assay.

How to write the identity block

  • “L-histidine free base, CAS 71-00-1, C6H9N3O2; not the hydrochloride.”
  • “Identification: IR conforms to reference, technique stated; HPLC retention conforms.”
  • “Assay 98.5–101.5% by HPLC on the dried basis; method, column and detection named.”
  • “Specific rotation −38.0° to −41.0° on the dried basis; solvent, concentration and temperature stated.”
  • “Loss on drying ≤0.5%; pH (1% solution) 7.0–9.0; chloride reported for each lot.”
  • “Related substances, including histamine, below the agreed limits; heavy metals and microbiology as on the catalog specification.”
  • “No added amino acids, salts or diluents; particle size ≥95% through 40 mesh or the agreed distribution.”

The composition statement turns identity into a specification. Make it part of the signed specification, not a later note, and state the chloride and histamine lines.

Five questions for the supplier

  1. Is this the free base or the hydrochloride, and which hydrate does the specification name?
  2. What are the specific rotation and its conditions, and what is the assay basis?
  3. What are the pH, chloride and water results for this lot?
  4. Can you send the HPLC chromatogram and the IR spectrum, not only the table of results?
  5. What are the histamine result and its limit, and which lot code ties the certificate to the drum?

The five replies should line up with the certificate and with each other. The product page carries the catalog specification; the COA page shows where each test sits; the grades page covers the form; the free-base-versus-hydrochloride page works through the label arithmetic; the methods section explains the chromatogram, and the quality page covers the retained-sample chain.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation