L-histidine free base or hydrochloride: choosing a grade
L-histidine is sold as the free base and as the hydrochloride, and the two are different label ingredients. The free base is C6H9N3O2 at 155.15 g/mol, with the whole mass present as histidine and a 1% solution at pH 7.0–9.0. The hydrochloride monohydrate is 209.63 g/mol, carries about 74.0% histidine, 16.9% chloride and 8.6% water of crystallisation, and gives an acidic solution. The catalog form here is the free base, a crystalline powder with at least 95% passing 40 mesh. The choice between the forms is set by the label, the dose and the matrix, not by which assay figure looks higher on a quotation.
The free base and the hydrochloride are different label ingredients: the salt adds chloride and water of crystallisation, so the declared name and the dose change with the form.
Why the form is a specification question
“L-histidine” on a purchase order is ambiguous. The free base and the hydrochloride share the histidine entity but not the molecular weight, the counter-ion, the solution pH or the label name. A certificate for one does not describe the other, and a formulation weighed for one will be wrong if the other arrives.
The second axis is physical form. The catalog grade is a crystalline powder with at least 95% passing 40 mesh; a milled or granulated grade is available on request. Mesh changes flow, dust and dissolution rate, not chemistry. Write both axes into the specification: the chemical form and the particle size.
Free base and hydrochloride side by side
| Line | L-histidine free base | L-histidine hydrochloride monohydrate |
|---|---|---|
| Label name | L-histidine | L-histidine hydrochloride |
| CAS | 71-00-1 | 5934-29-2 |
| Formula and molecular weight | C6H9N3O2 · 155.15 | C6H9N3O2·HCl·H2O · 209.63 |
| Histidine per gram | About 1.00 g | About 0.740 g |
| Chloride per gram | None added; monograph limit ≤0.05% | About 0.169 g |
| Water of crystallisation | None; loss on drying ≤0.5% | About 8.6% by theory |
| pH (solution) | 7.0–9.0 at 1% | 3.0–5.0 at 5% |
| Solubility in water | About 42 g/L at 25 °C | Freely soluble |
| Assay basis | 98.5–101.5% as histidine, dried basis | 99.0–101.0% as the salt, dried basis |
The table is not a ranking. Each form has a job, and the job is decided by the formula and by the label the brand intends to print. The catalog form is the free base; the hydrochloride is a different purchase with its own specification.
pH, solubility and handling
The free base is a zwitterion in water, not a strongly alkaline material. Its imidazole group has a pKa near 6.0, so a 1% solution sits at pH 7.0–9.0 and buffers in the mildly acidic range. That is a different behaviour from a strongly basic amino acid: the free base can be used in a blend without the aggressive neutralisation that a guanidino or primary amine side chain produces.
The hydrochloride is acidic in solution, roughly pH 3.0–5.0 at 5%, and it is freely soluble where the free base dissolves to about 42 g/L at 25 °C. That solubility difference is the practical reason to choose the salt: a concentrated stock, a cold process or a formula that needs a clear solution may not tolerate the free base. The price of that solubility is the chloride load and the water of crystallisation, both of which travel with the salt into the formula.
Both forms are hygroscopic to some degree. The free base is specified at loss on drying ≤0.5%, and an open pouch gains moisture in a humid room; the monohydrate has its water built into the crystal, but it can still pick up surface moisture. Keep both in the sealed pack and let a cold pack equilibrate before opening.
What the form does to the dose
The conversion is arithmetic. One gram of the hydrochloride monohydrate delivers about 740 mg of histidine, so a label that declares 500 mg of L-histidine needs 500 ÷ 0.740 = 676 mg of the monohydrate. The same 500 mg weigh-up of the salt delivers 370 mg of histidine, a shortfall of 26% against the declaration. Going the other way, a label that says 500 mg of L-histidine hydrochloride is declaring about 370 mg of histidine, not 500 mg.
The hydrate matters. The anhydrous salt, CAS 645-35-2 at 191.62 g/mol, delivers about 810 mg of histidine per gram; the monohydrate delivers about 740 mg. A specification that says only “hydrochloride” does not say which one, and the 8.6% water of crystallisation is enough to move a dose outside its tolerance. Name the hydrate in the specification and report water or loss on drying on the certificate.
The fill weight follows the arithmetic. A 500 mg capsule fill cannot deliver 500 mg of histidine from the salt: the salt needed for that dose weighs about 676 mg, and the chloride that comes with it is about 114 mg. A stick pack has more room, but the mass of the salt per portion is larger. Write the declared histidine figure, the form, the assay basis and the fill weight into the same document before the purchase order is placed.
What to write into the specification
- “L-histidine free base, CAS 71-00-1, C6H9N3O2; not the hydrochloride.”
- “Assay 98.5–101.5% by HPLC on the dried basis; specific rotation −38.0° to −41.0° on the dried basis, with the solvent and concentration stated.”
- “Loss on drying ≤0.5%; pH (1% solution) 7.0–9.0; chloride reported where the formula is salt-sensitive.”
- “Particle size ≥95% through 40 mesh, or the agreed milled or granulated distribution.”
- “Heavy metals and microbiology as on the catalog specification; lot code on the pack, the certificate and the retained sample.”
If the material is the hydrochloride, every line changes: the name, the CAS, the molecular weight, the assay basis, the pH range, the water and the chloride. A specification copied from the free base and applied to the salt is not a specification; it is a template with the wrong noun.
When the other form is the wrong answer
Do not choose the hydrochloride when the label has to read “L-histidine” and the dose is expressed as histidine, unless the label is changed to match the salt. Do not choose the free base for a formula that needs a concentrated clear solution at low pH and cannot tolerate the lower solubility. Do not switch forms to fix a flow problem: mesh and granulation are the tools for flow, and changing the salt to solve a hopper creates a labelling problem instead.
The catalog form is the free base at 40 mesh. The product hub carries the specification; the COA page shows how each line is reported; the free-base-versus-hydrochloride page works through the dose and label arithmetic; the stability page covers moisture and the pack; the compliance page covers the label name in each market.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation