What the COA for L-glutamic acid actually contains
Three questions decide an L-glutamic acid certificate: how much of the amino acid the lot contains, whether that amino acid is the L enantiomer, and how the powder behaves when it is weighed. The report answers them with an HPLC assay, a specific rotation on the dried basis, a loss on drying and a pH reading. Those lines sit among identification, particle size, heavy metals and microbiology. The figures below are the catalog limits; a lot is released only when its own COA reports results against them.
Three numbers carry the lot: the assay for quantity, the rotation for the L form, and the loss on drying for the basis the assay is reported on.
The certificate as a test report
A useful certificate can be checked without calling the supplier. Each line should show what was tested, how, and against which limit. “Conforms” is a conclusion, and a conclusion without the method behind it is hard to audit.
| Parameter | Method | Catalog limit |
|---|---|---|
| Appearance | Visual | White crystalline powder |
| Identification | IR and HPLC | Conforms to the reference |
| Assay | HPLC | 98.5–101.5% |
| Specific rotation | Polarimetry, dried basis | +31.0° to +32.5° |
| Loss on drying | Gravimetric | ≤0.5% |
| pH (1% preparation) | Potentiometry | 3.0–4.0 |
| Parameter | Method | Catalog limit |
|---|---|---|
| Particle size | Sieve analysis | ≥95% through 40 mesh |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
The pH row deserves a note. A 1% preparation is 10 g/L, while only about 8.6 g/L of L-glutamic acid dissolves at 25 °C. Unless the preparation is warmed, the reading comes from a saturated solution with solid still present. The method should say how the sample was prepared and at what temperature it was read.
The assay basis, the detector and the rotation conditions
An assay percentage needs a denominator. Reported “as is”, it includes the water the powder carries; reported “dried”, that water has been divided out. With loss on drying ≤0.5% the gap is small but real: 99.0% as-is on a lot with 0.4% water is about 99.4% on the dried basis. The certificate should print the basis in the assay row rather than leave it to a footnote.
Glutamic acid does not absorb usefully in the ultraviolet, so the HPLC method has to make the molecule visible. Common approaches are pre-column derivatisation, ion-exchange separation with post-column ninhydrin, or an evaporative light-scattering or charged-aerosol detector. “HPLC” on its own describes none of these; the detector, the standard and the sample preparation belong in the method. The HPLC method note explains the separation.
Rotation is measured on the dried basis, in 6 M hydrochloric acid by convention. The angle depends on the solvent, the concentration, the cell path and the temperature, so those details belong beside the result. A reading close to zero is not a weak batch of the L form; it indicates that the D form is present.
Release limit versus batch result
The catalog limit is the gate; the lot result is the evidence. They should sit in different columns, with the method beside them.
| Parameter | Catalog limit | Result column |
|---|---|---|
| Assay | 98.5–101.5% | A measured percentage, with basis and detector |
| Specific rotation | +31.0° to +32.5° dried basis | A measured angle, with solvent, concentration and temperature |
| Loss on drying | ≤0.5% | A measured percentage |
| pH | 3.0–4.0 | A measured value and the preparation used |
| Heavy metals | Per element | A measured figure in mg/kg for each element |
| Microbiology | Counts and absence | The count and the absence statement for the lot |
Some gates are tighter in practice than their number suggests. A rotation at the bottom of the window leaves little room for method variation. A loss on drying at 0.5% leaves no margin for a humid filling room. An assay above 101.5% is worth a check of the standard and the integration before it is accepted as a high-potency lot.
What moves between batches
Water and finishing account for most lot-to-lot movement. Drying changes the loss on drying; milling changes the mesh; the crystallisation step changes colour and habit. None of these is a change in the molecule, but each changes the certificate.
The rotation is the line to watch. If it drifts down across lots while the assay holds, the explanation is more likely a growing D fraction, a blended racemate or a change in the polarimetry conditions than a purity problem. Ask for the raw angle and the conditions, then confirm with chiral HPLC.
The lot code ties the document to the pack. It should appear on the certificate, on the pouch or drum, and on the retained sample.
When to order an outside test
An outside test is worth ordering when the source is new, the destination is regulated, the rotation is disputed, or the supplier's certificate does not address the D form. A focused panel is polarimetry with its conditions, chiral HPLC, IR against a reference, an HPLC assay with a named detector, loss on drying, ICP-MS and microbiology.
Add XRD when the solid form or a blend is at issue, and a nitrogen determination when a nitrogen-rich diluent is suspected. The report should state the detection limit for each screen; “not detected” without a limit says more about the method than about the sample. Keep the tested sample as the retained sample and record the lot code. The analytical methods index lists what each panel can show.
What to compare between suppliers
Compare suppliers on six lines: the enantiomer and CAS number, the assay with its basis and detector, the rotation with its conditions, the loss on drying, the pH with its preparation, and the contaminant and mesh results. Two lots that match on assay but differ on rotation are not the same material.
Then check traceability: who made the lot, which specification revision was used, and whether the lot code on the paper matches the pack. The catalog specification is on the L-glutamic acid product page; the form comparison is on the grades page; the tests that separate L from DL are on the identity page; the release workflow is on the quality page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation