06 Identity & adulteration

How we prove a sodium ascorbate lot is the salt

Technical document 06 · Reviewed 2026-11-20 · Sodium Ascorbate

On this page
  1. The four identity layers
  2. The sodium ratio: 11.6%
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A sodium ascorbate lot is the salt when four lines agree: the document names the monosodium salt and CAS 134-03-2, IR matches the ascorbate reference, sodium is close to the theoretical 11.6%, and pH sits in the 6.5–7.5 window rather than the acid's 2.1–2.6. The assay alone cannot separate the salt from ascorbic acid, a dilution or sodium erythorbate; sodium, pH and rotation are the tests that can.

In one line

Identity needs four agreeing lines: IR names the ascorbate, sodium proves the salt, pH separates it from the acid, and rotation excludes the erythorbate isomer.

The four identity layers

A document can name the correct salt and still leave it unproven. Each of the four layers below is a separate question with its own evidence, and a supplier who answers only the first has described paperwork rather than powder.

Four layers of sodium ascorbate identity
LayerQuestionTestWhat it proves
DocumentIs the form named?Name, CAS number, formulaPaperwork only
IRIs the anion ascorbate?FTIR against a referenceThe molecule family, not the salt
SodiumIs it the monosodium salt?ICP-OES or flame photometryThe counter-ion
RotationIs it the L form?Specific rotationExcludes sodium erythorbate
Mass balanceIs it diluted or wet?Assay, loss on drying, pHConsistency of the numbers

The IR spectrum is the catalogue identification. It shows the ascorbate functional groups, and it does not count the sodium. The sodium figure is the direct check on the salt, and the rotation is the check on the isomer. None of them is an assay.

The sodium ratio: 11.6%

The monosodium salt has one sodium ion per molecule. The theoretical sodium content is 22.99 ÷ 198.11 = 11.61% by mass, and the ascorbic acid equivalent is 176.12 ÷ 198.11 = 88.9%. A sodium result close to 11.6%, with an assay of 99.0–101.0% on the dried basis, is consistent with the salt.

A low sodium figure points to ascorbic acid, a dilution or a different cation; a high figure points to another sodium salt, a buffer or sodium chloride. The pH supports the reading: the salt sits at 6.5–7.5 in a 10% solution, while the acid sits at 2.1–2.6 in a 5% solution. A blend moves the pH toward the acid in proportion to the acid fraction.

Sodium by ICP-OES is not on the catalogue panel, so it is an additional test. Request it when the form is disputed, when a new source is qualified, or when the label names the salt and the certificate does not. Flame photometry or atomic absorption can answer the same question; name the method on the report.

X-ray diffraction and the solid state

X-ray diffraction answers the solid-state question: is the powder crystalline, and does the pattern match a reference? Sodium ascorbate is supplied as a crystalline powder, and a granulated grade is an agglomerate of the same crystals. XRD can distinguish that from an amorphous carrier or a different solid form, and it can compare lots from two sources.

XRD is not a purity assay and it does not measure the counter-ion. It is not a routine release test here. If a solid-form question matters to the process, ask for the pattern, the reference and the detection limit; a report that says only “XRD conforms” has added little.

For a disputed lot, XRD plus sodium plus IR is stronger than any one of them. The combination answers the solid, the salt and the molecule, and the assay closes the mass balance.

What adulteration looks like

Common sodium ascorbate substitutions and the signals
AdulterantWhat it doesSignalTest
Ascorbic acidNo sodium; pH fallsSodium below 11.6%; pH below 6.5%; assay above 101% if calculated as the saltSodium, pH, titration basis
Sodium erythorbateSame formula and sodium; cheaper isomerRotation +95.5° to +98° against +103° to +108°Specific rotation, chiral HPLC
Sugar or starchDilutes the powderAssay low; sodium low; loss on drying may riseMass balance, sodium
Other sodium saltRaises sodium, lowers assaySodium high; pH or ash movesICP-OES, chloride, ash
WaterRaises loss on dryingAs-is assay low; dried-basis assay normalLoss on drying
OxidationForms dehydroascorbic acidYellow or brown tint; HPLC shows the oxidation productHPLC, appearance

Colour is the weakest signal. White to off-white covers a wide range, and a yellow tint can come from oxidation or from a different drying step. The stronger signals are the sodium figure, the pH and the rotation. A certificate carrying appearance and assay but no identity evidence leaves the most likely substitution untested.

How to write identity into the specification

  • “Sodium ascorbate (monosodium L-ascorbate), CAS 134-03-2, C6H7NaO6.”
  • “Assay 99.0–101.0% on the dried basis by iodometric titration; HPLC for ascorbic acid and dehydroascorbic acid on request.”
  • “Identification by IR against a reference; report the sodium result by ICP-OES where the salt form is confirmed.”
  • “pH 6.5–7.5 in a 10% solution; loss on drying ≤0.5%.”
  • “Specific rotation +103° to +108° at 10% in water, where the erythorbate substitution is a risk.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No undeclared diluent; the form and CAS appear on the COA and the label.”

Write the form, the test and the expected result into the specification; a supplier cannot release against a name alone.

Five questions for the supplier

  1. Which form and CAS number are on the certificate?
  2. What is the sodium result by ICP-OES or flame photometry, and what method was used?
  3. What are the pH and loss on drying on the same lot?
  4. Can you provide the IR spectrum and, if the isomer is a risk, the specific rotation?
  5. If this lot is contested, would you agree to a joint re-test of the retained sample?

Those five answers together form an identity file; one assay figure on its own does not. The product page carries the catalogue specification; the COA page shows where each figure sits on the certificate; the grades page covers the physical options; the level-four comparison covers the label consequences; the vitamin C hub carries the acid; the XRD method note explains the solid-state check.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation