06 Identity & adulteration

How we prove an MSM lot is methylsulfonylmethane

Technical document 06 · Reviewed 2026-11-19 · MSM

On this page
  1. Four layers of identity
  2. Assay, purity and the sulfur ratio
  3. The solid-state check
  4. DMSO, DMSO2 and the other look-alikes
  5. How to write the identity block
  6. Five questions for the supplier

An MSM lot is identified by four layers: the lot documents and chain, the HPLC assay and purity, the melting range, and an IR spectrum against a reference. The name DMSO2 is a synonym for MSM; DMSO is a different molecule, and a certificate that confuses the two has not identified the material.

In one line

HPLC, melting range and IR have to agree, and the paperwork has to tie those results to the drum; a synonym is not an identity test.

Four layers of identity

Identity is not one test. It is a set of results that agree with each other and with the drum in front of the buyer. The layers below are independent enough that a swapped certificate or a mislabelled pack has a chance of showing up.

Four identity layers · MSM
LayerTestWhat it provesWhat it does not prove
DocumentCOA, lot code, retained sampleThe results belong to the lotThat the results are correct
ChromatographyHPLC assay and purityThe main component behaves as MSMWater, salts or the solid form
Physical constantMelting rangeThe solid is consistent with MSMA quantitative purity figure
SpectroscopyFTIR against a referenceThe functional groups matchHow much is present

The document layer is the one buyers skip. A certificate with a correct assay but no lot code, or a lot code that does not match the drum, is a result about some powder, not this delivery. The three analytical layers then have to agree: HPLC says MSM, the melting range sits inside 108.5–110.5 °C and the IR matches the reference.

Assay, purity and the sulfur ratio

MSM is C2H6O2S, one sulfur atom in a molecule of 94.13 g/mol; sulfur is 34.06% of the mass. That ratio is a useful cross-check: a reported sulfur result should agree with the assay within the uncertainty of both methods. A sulfur figure that implies more or less MSM than the assay allows is a reason to look at the method and the sample.

The assay and the chromatographic purity are not the same ratio. The assay is a quantitative result against a reference standard, reported on the anhydrous basis; the purity is the MSM peak area divided by the total integrated area. A lot can be 99.9% pure by area and 99.0% by assay because water and inorganic residue do not appear in the chromatogram. The gap between the two numbers is where those components live.

The ratio also catches arithmetic errors. A certificate that reports 101.5% assay is outside the catalog window; 99.9% purity with a 98.5% assay is not necessarily wrong, but the gap needs an explanation. Ask for the loss on drying and the residue before deciding which number is the outlier.

The solid-state check

The melting range is the routine solid-state test. A pure crystalline solid melts sharply, and the catalog window of 108.5–110.5 °C is narrow enough to catch a material that is wet, cut with a low-melting residue or not the named substance. It is an identity and consistency check, not a purity assay: a eutectic mixture can melt over a range, and a pure material can read a degree low if the thermometer is off.

X-ray diffraction is the deeper solid-state check. A diffraction pattern fingerprints the crystal lattice, so it can distinguish a different crystal form or a crystalline look-alike that the melting range cannot resolve. It is not a routine release test or a purity assay; it sees crystalline phases above its detection limit, not water or amorphous content. Ask for XRD when a supplier claims a special crystal form, when qualifying a new source, or when the melting range is ambiguous.

Differential scanning calorimetry can confirm the melting transition, but the capillary range on the certificate is enough for release. The extra technique helps when the basic layers disagree.

DMSO, DMSO2 and the other look-alikes

Look-alikes and impurities · what they are and how they show
NameWhat it isHow it shows
DMSODimethyl sulfoxide, C2H6OS, CAS 67-68-5; a different molecule and a common precursorResidual solvent by GC; melting range depression
DMSO2A synonym for MSM, not a separate homologueCheck the CAS: 67-71-0 is MSM
Sulfate or sodium sulfateA white, water-soluble inorganic diluentResidue on ignition, ion chromatography, low assay
Dimethyl sulfideA volatile sulfur species with a strong odourGC and odour; may not separate by HPLC
WaterMoisture picked up in handlingLoss on drying; as-is assay

The naming confusion is simple. DMSO2 is the same molecule as MSM; a supplier selling “DMSO2” is selling MSM. DMSO is a different solvent, with CAS 67-68-5, a different formula and a melting point of about 18.5 °C. A certificate that lists DMSO as a residual impurity is plausible for an oxidation route; a certificate that uses DMSO as the product name is a different product.

Sulfate is the dilution risk a UV-based HPLC method can miss. Sodium sulfate is white, soluble and has no chromophore at the detection wavelength, so it can add mass, lower the assay and leave the purity looking clean. Residue on ignition and ion chromatography see it. A high residue with a clean HPLC is a signal to ask for the ash composition.

Dimethyl sulfide is the odour risk. A sulfurous smell on an otherwise white powder can come from a trace volatile species the HPLC method does not resolve. It is not proof of adulteration; ask for the GC data and the drying step. Water is the least exotic explanation: a lot that was dry at release can pick up moisture in an open drum, and the caking looks like a quality problem but is a pack problem.

How to write the identity block

  • “Methylsulfonylmethane (dimethyl sulfone), CAS 67-71-0, C2H6O2S.”
  • “Assay 99.0–101.0% on the anhydrous basis by HPLC; chromatographic purity ≥99.8%.”
  • “Melting range 108.5–110.5 °C; FTIR spectrum conforms to the reference.”
  • “Loss on drying ≤0.5%; residue on ignition ≤0.1%; ≥95% through 40 mesh.”
  • “Residual DMSO: report the result and agree the limit for the application.”
  • “Sulfate: report the result and agree the limit for the application.”
  • “Lot code on the COA, the drum and the retained sample.”

The residual DMSO and sulfate lines are not in the catalog specification, and they should not be invented as fixed numbers. They are clauses to agree when the route or the application makes the residue relevant. A specification that says only “MSM 99%” leaves the identity, the water and the inorganic fraction open.

Five questions for the supplier

  1. What is the manufacturing route, and is DMSO the precursor?
  2. What is the residual DMSO result, and which method produced it?
  3. Is sulfate or ash reported, and what limit applies to this grade?
  4. Does the certificate include the melting range and an FTIR spectrum against a reference?
  5. Can the COA, the drum and the retained sample be tied to one lot code?

Five direct answers amount to an identity file. A single assay percentage does not. The COA page sets out the certificate lines; the compliance page covers the market file; the MSM hub carries the catalog specification. The HPLC and FTIR notes explain the methods.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation