06 Identity & adulteration

How we prove a coenzyme Q10 lot is ubiquinone

Technical document 06 · Reviewed 2026-11-20 · Coenzyme Q10

On this page
  1. The four identity layers
  2. The redox ratio and the homologue ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A coenzyme Q10 lot is ubiquinone when four lines agree: the document names CAS 303-98-0 and the oxidised form, HPLC retention and UV at 275 nm match the reference, the melting point and infrared spectrum match the solid, and the mass balance closes with the loss on drying and the related-substance profile. An assay percentage alone does not separate ubiquinone from ubiquinol, a Q9-rich mixture or a dilution.

In one line

Identity is the agreement of four measurements: HPLC retention and UV say the quinone, the melting point and IR say the solid, and the redox ratio says the form.

The four identity layers

A certificate can name the right material and still fail to prove it. The four layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of coenzyme Q10 identity
LayerQuestionTestWhat it proves
DocumentIs the form and CAS named?Name, CAS 303-98-0, formulaPaperwork only
ChromatographyIs the quinone coenzyme Q10?HPLC retention, UV at 275 nm, related substancesThe molecule, not the form
SolidIs it crystalline ubiquinone?Melting point, infrared spectrumThe solid form
Mass balanceIs it diluted or partly reduced?Assay, loss on drying, redox ratio, impuritiesConsistency of the numbers

The document layer is necessary but weak: a certificate can carry the right name and the wrong powder. The chromatography layer is the strongest single test, but a 275 nm assay calibrated for ubiquinone is blind to ubiquinol unless the method is set up to see both. The solid layer catches a different failure, such as an amorphous or melted material. The mass balance catches dilution and moisture.

The redox ratio and the homologue ratio

Ubiquinone and ubiquinol absorb differently and elute differently. A dual-wavelength HPLC method can read ubiquinone at 275 nm and ubiquinol at 290 nm, and report the two as a ratio. That ratio is the form check. A single peak reported as “total CoQ10” after an oxidation step measures the sum and destroys the information about which form was present.

For a ubiquinone lot, the useful question is how much ubiquinol is present, not whether the reduced form is the main component. For a ubiquinol lot, the catalog sets ubiquinone at ≤2.0%, because the reduced form oxidises back to ubiquinone in air and light. In both directions, the ratio is a form check rather than a potency check.

The second ratio is the homologue profile. Coenzymes Q7, Q8, Q9 and Q11 share the quinone head and differ in the number of isoprene units. Coenzyme Q9 is the pharmacopoeial related compound A, and a Q9-rich side fraction can pass a total quinone assay while failing the Q10 identity. The chromatogram should name the homologues it bounded and the relative retention of each.

X-ray diffraction and the solid state

X-ray diffraction answers a question the assay cannot: is the solid crystalline, and does its pattern match a reference? Ubiquinone can be crystalline, and its melting range of 48–52 °C is consistent with a crystalline solid that softens at a modest temperature. A melted and re-solidified lot may retain the same assay while its diffraction pattern and bulk density change.

XRD is not a routine release test for this product, and a certificate that says only “XRD conforms” without the pattern, the reference and the detection limit has added little. Ask for those three items when solid form is the dispute. XRD is not a form-specific assay: it describes the packing of the solid and needs a reference pattern for each form.

For a disputed lot, XRD plus melting point plus HPLC/UV is stronger than any one of them. The combination separates a crystal-form problem from a purity problem and from a form problem.

What adulteration looks like

Coenzyme Q10 substitutions and the signals that expose them
AdulterantWhat it doesSignalTest
UbiquinolReduced form; different colour and stabilityResponse at 290 nm; ratio shiftDual-wavelength HPLC
Coenzyme Q9Shorter side chain; related compound AExtra peak at relative retention about 0.75HPLC related substances
DilutionLowers assay; changes loss on dryingAssay low; ash or carrier presentMass balance, infrared
Oil or carrierLowers assay per gramGreasy feel; extractable matterAssay, infrared, extraction
DyeMatches the yellow-orange colourColour without a UV or IR matchUV spectrum, infrared, HPLC
(2Z)-IsomerLight- or heat-formed geometric isomerExtra peak near the main peakHPLC isomer method

Colour is the weakest signal. Yellow to orange-yellow covers a wide range, and a dye can reproduce it. The stronger signals are the chromatographic profile, the melting point and the infrared spectrum. A certificate that reports appearance and assay but not identity has left the most likely substitution untested.

How to write identity into the specification

  • “Ubiquinone (coenzyme Q10), CAS 303-98-0, C59H90O4, oxidised form.”
  • “Assay 98.0–101.0% by HPLC on the anhydrous basis; loss on drying ≤1.0%.”
  • “Identification by HPLC retention and UV spectrum at 275 nm; report the chromatogram.”
  • “Melting point 48–52 °C; add infrared identity where the pharmacopoeial file requires it.”
  • “Related substances: coenzymes Q7, Q8, Q9 and Q11 and the (2Z)-isomer within the agreed limits.”
  • “Redox ratio: ubiquinol bounded by the agreed limit; report the method.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”

Identity is not a single line on a certificate. It is the set of lines that agree, and the specification should ask for all of them when the form matters.

Five questions for the supplier

  1. Which form is this lot, and which CAS number is on the certificate?
  2. Can you provide the HPLC chromatogram with the related-substance peaks, not only the assay percentage?
  3. What are the melting point and the infrared spectrum for this lot?
  4. What is the ubiquinol result, and which method and wavelength were used?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page covers the presentations; the level-four comparison covers the reduced form; the HPLC method note explains the separation.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation