02 Grade comparison

Shark chondroitin grades: purified powder, granulation and mesh

Technical document 02 · Reviewed 2026-11-20 · Chondroitin Sulfate Shark

On this page
  1. Why the shark grade is defined by three figures
  2. The forms and what changes between them
  3. Powder, flow and the 80 mesh cut
  4. Dosage forms and fill
  5. What to write into the specification
  6. When a different grade is the wrong purchase

Shark chondroitin sulfate is supplied as a purified powder specified at 90.0–105.0% by CPC titration on the dried basis, with sulfate at 15.0–20.0%, protein at ≤5.0% and a particle size of ≥95% through 80 mesh; granulated material is available on request. Those figures define the grade. The mesh and the granulation are finishing choices made for the filling line, not a different chemical specification. A milled shark cartilage powder is a separate product and should not be ordered against this description.

In one line

The grade is fixed by three numbers — the CPC assay on the dried basis, the sulfate figure and the protein — before the mesh or the granulation is chosen.

Why the shark grade is defined by three figures

The chondroitin sulfates are a family of sulfated glycosaminoglycan chains, and a shark grade is defined by how much of that family the powder carries and how much cartilage protein is left beside it. The catalog ties three figures together: assay 90.0–105.0% by CPC on the dried basis, sulfate 15.0–20.0%, protein ≤5.0%. They move together. Protein and water can be removed to push the assay up, and a carrier can dilute the powder back below the window. Reading one figure without the other two is how a grade gets misdescribed.

Shark cartilage is also sold as a milled cartilage powder. That material contains chondroitin sulfate among other cartilage components and its chondroitin figure is far lower. It has food uses, but it cannot stand in for the purified grade on a capsule label that declares a chondroitin sulfate amount. The word “shark” on an inquiry does not say which of the two is meant.

The forms and what changes between them

Shark chondroitin forms and what changes between them
FormChondroitin figureCompositionTypical use
Purified powder, 80 mesh90.0–105.0% CPC, dried basisProtein ≤5.0%; sulfate 15.0–20.0%Capsules, tablets, blends
Purified powder, granulatedSame assay windowSame limits; flow and bulk density changeHigh-speed capsule and tablet lines
Milled shark cartilageNot this specification; chondroitin is a fractionProtein and ash much higherFood uses, not a gram-dose chondroitin
Blend with a carrierAssay stated on the blendCarrier changes the labelLow-dose formats

The first two rows are the same ingredient at two finishing cuts. The third is a different product and the fourth is a dilution; neither is a grade of the purified powder. A supplier who quotes a “shark chondroitin 90%” should say which row applies.

Powder, flow and the 80 mesh cut

The catalog powder is white to off-white and free-flowing, with ≥95% passing 80 mesh, and it dissolves in water to a viscous solution. The 80 mesh cut is a finishing step: a new mill or sieve can move it with no change to the chemistry. A finer cut disperses faster in a blend but can dust and cake; a coarser cut flows better but may leave a gritty mouthfeel in a stick pack.

Bulk density and flow also depend on moisture and on granulation. A powder stored in a humid room before filling will bridge in the hopper even though the certificate is unchanged. Colour and odour are practical checks: a grey or yellow tinge, or a strong fishy smell, points to residual protein or a warm drying step. The catalog has no odour limit, so a sensory check belongs in the incoming inspection.

Dosage forms and fill

Chondroitin is dosed in grams, so the assay determines how much powder goes into each unit. A 90% powder and a 100% powder do not fill the same capsule at the same declared amount, and the difference shows up in capsule size, count per bottle and the cost of the format. Choose the capsule size only after the assay window and the mesh are set, not after the first filling trial.

A tablet line needs a powder that compacts without sticking; granulation may be the answer, and it is a separate specification line. A powder blend or stick pack wants a powder that wets out without lumps; residual protein can make the drink foam when it is shaken. None of these choices changes the assay, but each changes the material the line receives.

What to write into the specification

  • “Chondroitin sulfate from shark cartilage, CAS 9007-28-7; species and tissue stated on the lot file.”
  • “CPC assay 90.0–105.0%, measured on the dried basis, with the standard declared.”
  • “Sulfate 15.0–20.0%; protein ≤5.0%; loss on drying ≤10.0%.”
  • “Identification by CPC and HPLC conforming to the reference; chromatogram available.”
  • “Particle size ≥95% through 80 mesh; granulated on request.”
  • “Heavy metals and microbiology as listed; fish allergen assessment and species statement on file.”

We supply the purified shark grade at 80 mesh, granulated on request, with the species statement and the fish allergen assessment issued for the lot. The shark hub lists the catalog data; the COA page shows how the figures are reported; the shark versus bovine comparison covers the source decision; the bovine product page is the terrestrial alternative.

When a different grade is the wrong purchase

If the label names a terrestrial source, or the customer's allergen policy excludes fish, this grade is the wrong purchase even when the assay is higher than the bovine alternative. If the formula needs a cartilage powder rather than a purified chondroitin, the 90% specification is the wrong specification. If the label declares a specific salt form, the certificate has to name that salt, not only “chondroitin sulfate”.

A change of source or form starts a new ingredient file. The artwork, the customer's sign-off, the specification, the species statement and the allergen assessment travel as one package. The compliance page sets out the fish allergen and fisheries documents; the identity page covers the tests that separate shark material from another source; the quality page covers release and retention; the methods index explains the assay and contaminant panels.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation