How we prove a lot is porcine chondroitin sulfate
A porcine chondroitin sulfate lot is identified from four agreeing lines: the species and tissue declaration, the CPC assay on the dried basis, the HPLC profile against a reference, and the sulfate, protein and moisture figures. The assay measures charge-bearing material; it does not name the species. The species claim rests on the source file and, where it is disputed, on a species-specific test of the raw material.
The CPC assay says how much sulfate-bound material is present; the species declaration, the HPLC profile and the sulfate-to-protein balance say whether it is porcine chondroitin.
The four identity layers
Identity is a conclusion from independent evidence, and each layer answers a different question.
| Layer | Evidence | Question it answers |
|---|---|---|
| Source | Species, tissue, origin and lot trail | Does the paperwork name the animal and the tissue? |
| Assay | CPC titration, dried basis, declared standard | How much charge-bearing material is in the powder? |
| Chromatography | HPLC profile versus a reference | Does the chain profile match the standard? |
| Composition | Sulfate, protein, moisture and contaminants | Is the powder wet, diluted or under-purified? |
Each layer is independent. A true source statement does not stop a diluted powder. A passing assay does not stop a different chromatogram. A clean chromatogram does not stop moisture at the ceiling. Only four agreeing answers close the file.
Sulfate, protein and the balance between them
The sulfate figure for this grade is 15.0–20.0%, and protein is ≤5.0%. Both are composition lines that sit beside the assay, and the pair is a useful consistency check. CPC binds both sulfate and carboxylate groups, so a powder made largely of a less-sulfated glycosaminoglycan can still consume CPC and read inside the assay window while the sulfate figure falls.
Protein points the other way. A high protein result at a normal sulfate figure suggests incomplete digestion or washing rather than a different polysaccharide; a low protein result at a normal sulfate figure is one sign that purification did its job. Neither figure is a purity statement, and the balance is not a release calculation. It is a check that the three numbers tell one story.
The salt form deserves the same attention. The catalog does not print a sodium line for this grade, so where the label declares a sodium salt, the specification should say so and the certificate should support it. The CPC assay cannot answer that question on its own.
X-ray diffraction and the solid state
Chondroitin sulfate is a hygroscopic polymer, and its powder pattern is a broad halo rather than a set of sharp peaks. XRD therefore cannot identify the material in the way it identifies a crystalline salt, cannot separate chondroitin from dermatan or heparan sulfate, and cannot name the species. A report that says “XRD conforms” without a reference pattern has added little.
The method has a narrow role as a screen for crystalline adulterants. Sodium chloride, sugar or a mineral filler shows sharp peaks against the halo, which is useful when dilution is suspected. A low level of an adulterant can sit below the detection limit, so a clean scan is not a clean lot. Ask for the reference and the detection limit before reading a match statement.
What adulteration looks like
| Route | Effect on the sheet | Test that exposes it |
|---|---|---|
| Other glycosaminoglycans | Dermatan, heparan or hyaluronic material also binds CPC and can stain | HPLC profile plus the sulfate figure against a reference |
| Low-molecular-weight fraction | The charge response changes with chain length | Declared molecular weight; standard matched to the lot |
| Salt or sodium chloride | Mass without chondroitin | Dried-basis assay; pH and conductivity |
| Maltodextrin or sugar | Dilutes the powder and raises moisture | Assay, protein and HPLC; carbohydrate profile |
| Protein filler | Mass and a raised protein figure | Protein result plus the chromatographic profile |
| Undeclared species | Same assay, different animal and paperwork | Species-specific raw-material test; source records |
No single test catches every route. The screen that works combines the assay against a declared standard, the HPLC profile, sulfate and protein, moisture, and a source statement that agrees with the label. Apply it before acceptance, independent of the commercial terms.
Writing identity into the specification
- “Porcine chondroitin sulfate, CAS 9007-28-7, from porcine cartilage (trachea or nasal septum), country of origin stated.”
- “Assay 90.0–105.0%, dried basis, by CPC titration against a declared standard.”
- “Identify by CPC reaction and HPLC against a reference, and file the chromatogram with the lot.”
- “Sulfate 15.0–20.0%; protein ≤5.0%; loss on drying ≤10.0%.”
- “≥95% through 80 mesh; heavy metals and microbiology to the listed limits.”
- “Species and tissue declaration on file; a species-specific test on the raw material where the source is disputed.”
Five questions for a supplier
- What species and tissue does the lot come from, and where was the raw material sourced?
- Which reference standard and titration mode underpin the CPC result, and what chain-length range does that standard represent?
- Can the HPLC chromatogram and its reference be released, not just the assay figure?
- What are the lot's sulfate, protein and loss-on-drying results, and by which methods were they obtained?
- If the species is challenged, will you open the raw-material records and release a retained sample for a species-specific test?
The product page holds the specification; the COA page shows where each figure sits; the source page compares the three sources; the bovine hub holds the other source; the methods index covers the chromatographic, contaminant and microbiology panels.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation