06 Identity & adulteration

How we prove an oat beta-glucan lot is the mixed-linkage cereal polymer

Technical document 06 · Reviewed 2026-11-20 · Beta-Glucan Oat

On this page
  1. Four checks, four different questions
  2. The 1,3 to 1,4 linkage ratio
  3. X-ray diffraction: what it can and cannot show
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Six questions for the supplier

A beta-glucan assay returns glucose, and glucose is the one thing oat, barley, yeast and cellulose share. That is why an oat beta-glucan identity file cannot rest on the percentage alone. It needs four agreeing checks: the oat source and fraction, the named cereal assay, the mixed 1,3/1,4 linkage pattern, and a mass balance that leaves no room for a carrier.

In one line

A beta-glucan assay measures glucose, and glucose is the one thing oat, barley, yeast and cellulose have in common; identity needs the source record and the 1,3/1,4 fingerprint beside the percentage.

Four checks, four different questions

Oat beta-glucan identity checks
CheckQuestion it answersEvidenceLimit of the evidence
SourceIs the material from oats?Name, CAS 9012-72-0, oat fraction, supplier auditPaperwork and process, not the powder
AssayHow much beta-glucan is present?Cereal enzymatic method with a stated basisA glucose-based figure, not a source test
LinkageIs it the mixed 1,3/1,4 polymer?Lichenase digest or methylation analysisStructural family, not quantity
BalanceIs it diluted or extended?Moisture, protein, ash, starch, sugar profileConsistency, not identity by itself

The four are complementary, and none is sufficient alone. A source record without an assay describes a purchase; an assay without a linkage check describes glucose; a linkage check without a mass balance can still miss a blend that carries the right polymer at a lower level.

The 1,3 to 1,4 linkage ratio

The mixed-linkage pattern is the most useful structural fact about oat beta-glucan. The chain is unbranched, and roughly three of every ten linkages are 1,3 while seven are 1,4. That is not a random copolymer: the 1,3 links break up the cellulose-like 1,4 runs, which is why the polymer dissolves and thickens water instead of behaving like cellulose.

Lichenase reads that pattern directly. The enzyme cuts the chain where a 1,4 bond follows a 1,3 link and releases two characteristic fragments, one with three sugars and one with four. The ratio of the DP3 fragment to the DP4 fragment is about 1.5–1.7 in oat and about 2.3–2.7 in barley, so the digest is a cereal fingerprint, not just a glucose count. HPAEC-PAD can read the fragments; methylation followed by GC-MS gives the linkage proportions independently.

None of this is a routine release test. The catalog states the linkage family; a lot-specific ratio is a qualification tool used when a source is new or a result is contested. Ask for the chromatogram or the linkage table, not for the word “conforms”.

X-ray diffraction: what it can and cannot show

X-ray diffraction is the wrong instrument for the source question, and it is worth knowing that before paying for it. XRD sees crystalline order. A dried oat beta-glucan powder is amorphous, so the expected result is a broad halo with no sharp reflections; the halo says the powder is not crystalline, not that it is oat.

The method has one narrow use in this file: detecting a crystalline carrier or filler in a blend. Dextrose, sucrose, lactose or a mineral salt would produce sharp peaks, and that is a formulation question. XRD cannot measure beta-glucan, cannot separate oat from barley, and does not belong in a release specification. If a supplier offers “XRD conforms”, ask what reference was used and what the detection limit was.

What adulteration looks like

Common oat beta-glucan substitutions and the signals
SubstituteWhat it changesSignalCheck
Maltodextrin or glucose syrupAdds soluble solids without beta-glucanBeta-glucan low; free glucose highEnzymatic assay and sugar profile
Oat flour or starchDilutes the concentrate with alpha-glucanStarch high; protein and ash shiftAlpha-glucan digestion and iodine test
Barley beta-glucanSame linkage family, different sourceDP3 to DP4 ratio above the oat rangeLichenase digest by HPAEC-PAD
CelluloseAdds beta-1,4 bulk that the assay may not countInsoluble residue; recovery changesLinkage analysis and microscopy
Yeast beta-glucanSupplies glucose under the same nameSource record inconsistent; 1,6 branches presentLinkage analysis and source audit
Protein or ash fillerAdds mass; shifts the balanceProtein or ash over the limitNitrogen determination and ashing
WaterLowers the as-is resultMoisture high; dry-basis figure normalLoss on drying

Appearance is the least useful check. Off-white to light tan covers a wide range, and a blend can reproduce it. The checks that see structure or the mass balance are the ones worth trusting: the DP3 to DP4 pattern, the starch figure, the sugar profile and the moisture-protein-ash triangle.

How to write the identity into the specification

  • “Oat beta-glucan concentrate, CAS 9012-72-0, (C6H10O5)n, from Avena sativa.”
  • “Beta-glucan ≥70.0% by the named cereal enzymatic method; state the basis.”
  • “Moisture ≤7.0%; protein ≤5.0%; ash ≤3.0%.”
  • “Identification by enzymatic beta-glucan profile; mixed 1,3/1,4 linkage stated.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”
  • “No added maltodextrin, glucose, starch or other carrier unless declared and quantified.”

The linkage statement is the line that separates oat from a generic beta-glucan. The COA page shows where each result sits on the certificate.

Six questions for the supplier

  1. Which oat fraction and which fractionation process produced this lot?
  2. What procedure and kit did the laboratory use, and was the figure calculated on the powder as received or on the dried solids?
  3. Can you provide the lichenase digest or the linkage analysis behind the mixed 1,3/1,4 claim?
  4. What are the moisture, protein and ash results, and how do they close the mass balance?
  5. What is the gluten and allergen position for the oat supply chain?
  6. If the source or linkage is contested, would you join a re-test of the sealed reference sample?

Six answers amount to an identity file; one assay percentage does not. The oat beta-glucan product page carries the catalog specification; the grades page compares the concentration bands; the level-four comparison takes the source question further; the yeast product is on the beta-glucan page; the methods library describes the procedures; the quality page covers release.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation