Oat beta-glucan grades: concentration, particle size and the fill
Oat beta-glucan is sold as a concentration ladder rather than a single grade: a lower-concentration oat fibre, the ≥70.0% concentrate specified here, and higher-purity fractions. The percentage decides how much powder carries a given beta-glucan mass, and the physical form decides how that powder flows, disperses and fills. The catalog grade on this page is the ≥70.0% powder at 80 mesh.
The grade is two decisions, not one: the beta-glucan concentration sets the mass per serving, and the particle form sets how the powder behaves in the mixer.
Why oat beta-glucan has grades
Oat grain contains beta-glucan at a few percent, mixed with starch, protein, lipid and bran. A concentrate is made by separating the soluble fibre from the rest, and how far that separation goes is the grade. A 25% oat fibre and a 70% concentrate can both be sold as oat beta-glucan, and they are not interchangeable in a capsule or a drink.
The non-beta-glucan fraction is not inert filler. It brings its own protein, starch, colour and water-binding, so a lower grade changes the taste, the flow and the moisture behaviour as well as the mass. A higher grade reduces the carrier per gram of beta-glucan, which matters when the serving is a single capsule or a small stick.
The concentration bands side by side
| Grade | Beta-glucan | What the powder carries | Typical use |
|---|---|---|---|
| Oat fibre | About 20–30% | Starch, protein and bran alongside the fibre | Bakery, cereal, bulk fibre |
| Concentrate | ≥70.0% (catalog) | Protein ≤5.0%, ash ≤3.0%, moisture ≤7.0% | Capsules, sticks, drink mixes |
| High-purity fraction | Above 80% | A narrower fraction with less carrier per gram | Small capsules, concentrated formats |
| Granulated concentrate | ≥70.0% on request | The same chemistry at a coarser particle size | Flow and dust control |
The bands are market descriptions, not a ranking. This catalog specifies the ≥70.0% concentrate; the other rows are here so that a quotation naming them can be read against the same questions. Whatever the band, the specification needs the method, the basis and the particle size beside the percentage.
Particle size, colour and viscosity
The catalog powder is ≥95% through 80 mesh, which is a fine powder of about 177 µm and below. It hydrates quickly, dusts easily and can bridge in a hopper; granulation coarsens it and improves flow without changing the beta-glucan figure. The colour is off-white to light tan, and a concentrate with more bran fraction is usually darker.
In water the powder disperses and thickens. Viscosity depends on concentration, molecular weight, particle size, shear and temperature, so a viscosity figure is only meaningful with the solids level and the method stated. A fine powder hydrates faster than a granule, which helps a stick pack and can slow a tablet press. The powder is hygroscopic, and a humid filling room turns a free-flowing lot into a sticky one before the pack is sealed.
Sizing a serving and a fill
Grade arithmetic starts from the beta-glucan figure. At 70.0%, one gram of powder carries 0.70 g of beta-glucan; a 500 mg capsule fill carries 350 mg; to declare 500 mg, the formulator weighs 714 mg of powder. If a formula targets 3 g of beta-glucan, it needs 4.29 g of the 70% powder. None of these figures is a dose recommendation; they are the conversions that keep the label, the fill weight and the assay in agreement.
Check the basis before using the factor. If 70.0% is on the dried basis and the powder carries 5.0% moisture, the as-is figure is 66.5%, and the same label claim needs more powder. The certificate, the specification and the label should share one basis, and the conversion should be written into the batch record rather than applied from memory.
A lower grade is not wrong for every application. In a bakery or a cereal, the carrier fraction is part of the food and a larger mass may be acceptable; in a small capsule, the carrier mass is the constraint and a higher grade earns its place. The choice is a fit between the serving and the powder, not a preference for a bigger number.
What to write into the specification
- “Oat beta-glucan concentrate, CAS 9012-72-0, (C6H10O5)n, from Avena sativa.”
- “Beta-glucan ≥70.0% by the named cereal enzymatic method; state the basis.”
- “Protein ≤5.0%; moisture ≤7.0%; ash ≤3.0%.”
- “Particle size ≥95% through 80 mesh; granulated on request.”
- “Identification by enzymatic beta-glucan profile; heavy metals and microbiology as listed.”
- “Oat source, gluten statement and any carrier declared.”
Write the grade as a concentration plus a form. “70% powder, 80 mesh” and “70% granulated” are two packs of one chemistry, and the specification should say which one is being bought. The oat versus yeast comparison takes the source question further.
When a different grade or source fits better
When the beta-glucan target is modest and the carrier fraction is acceptable, a lower grade can meet the brief with less processing. When the serving is a single capsule or a small stick, the carrier may not fit and a higher grade is the practical choice. When the label or the market file names yeast beta-glucan, none of these oat grades is a substitute: the source is a different product, with a different linkage and a different claim position.
The oat beta-glucan product page carries the catalog specification; the COA page shows how the beta-glucan figure is reported; the compliance page covers the market file; the yeast product is described on the beta-glucan page; the methods library describes the assays; the quality page covers release.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation