01 COA & batch testing

What the COA for wheat gluten actually contains

Technical document 01 · Reviewed 2026-11-20 · Wheat Gluten

On this page
  1. What the certificate has to show
  2. Dry basis, the nitrogen factor and the gluten method
  3. The limit and the measured result
  4. What changes from lot to lot
  5. When an outside laboratory helps
  6. Comparing suppliers line by line

A wheat gluten certificate reports appearance, protein by Kjeldahl with its nitrogen factor and basis, gluten content with the method used, moisture, ash, the protein-profile identification, particle size, heavy metals and microbiology. The catalog limits are in the table below; the lot COA is the evidence that a particular pack met them. Protein and gluten are separate lines, and a certificate that prints the same number twice has not shown two measurements.

In one line

Protein and gluten are two lines, not one: the nitrogen factor, the moisture correction and the gluten method decide what the percentage on the certificate actually describes.

What the certificate has to show

A certificate earns its place when a reviewer can rebuild the release decision from the page. Every line should carry the parameter, the method behind the number and the limit used for release. A row that gives only “conforms” offers a verdict with no evidence.

The identification line and the protein line answer different questions. Identification says the powder has the protein profile of wheat gluten; the protein figure says how much nitrogen-rich material is present.

Release parameters for wheat gluten
ParameterMethodRelease limit
AppearanceVisualOff-white to cream powder
IdentificationProtein profile by SDS-PAGE or HPLCConforms to the reference
ProteinKjeldahl, N × 5.7, dry basis≥75.0%
Gluten contentNamed washing or protein-based method≥75.0%
MoistureLoss on drying≤8.0%
AshGravimetric≤1.0%
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent
Particle sizeSieve analysis≥95% through 80 mesh

Dry basis, the nitrogen factor and the gluten method

Kjeldahl digestion converts nitrogen to ammonia and measures it; the protein figure is that nitrogen multiplied by a factor. The catalog uses 5.7 and states the dry basis, so both conventions are fixed on the certificate. Codex Standard 163-1987, the reference for wheat protein products including wheat gluten, uses a factor of 6.25 and a minimum of 80% for wheat gluten. The same catalog figure restated with the Codex factor is 75.0 × 6.25 ÷ 5.7 = about 82.2%, which is the number to quote when a customer's specification follows that standard.

The moisture correction is the second arithmetic step. A lot measured at 78.0% protein as received, with 7.0% moisture, is 78.0 ÷ 0.93 = 83.9% on the dry basis. Run the other way, 75.0% dry basis at the 8.0% moisture limit is 75.0 × 0.92 = 69.0% as received. A 75.0% figure without its basis could describe either powder.

The gluten line needs its own method. A washing method recovers the water-insoluble gluten mass; a gluten-index test adds a centrifugation step; a protein-based calculation derives gluten from nitrogen. The three are not interchangeable, and the catalog's ≥75.0% has to say which one it means and whether the result is dry or as received.

The limit and the measured result

The release limit is the acceptance boundary; the result is what the laboratory found on the lot. They belong in separate columns, with the method beside them. If the result column simply repeats the specification range, it is a copy of the limit, not evidence about the powder.

What belongs in the result column
ParameterRelease limitResult column
Protein≥75.0% (N × 5.7, dry basis)A measured percentage, with the factor and the moisture result
Gluten content≥75.0%A measured percentage, with the method and the basis
Moisture≤8.0%A measured percentage
Ash≤1.0%A measured percentage
Heavy metalsPer elementA measured figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

“Passes specification” should be a conclusion the reader can reach from the numbers. For heavy metals that means a figure per element, not a total that hides the one element close to its limit. For microbiology it means a count plus an absence statement. For gluten it means the method, because a percentage without a method cannot be compared with another supplier's certificate.

What changes from lot to lot

Wheat source and crop year set the starting protein, the gluten strength and the ash. Milling and air classification move the particle size and can concentrate protein; drying moves the moisture and, if the heat is excessive, the vitality of the gluten. A new crop year is a change of raw material even when the specification is unchanged, and it belongs in the supplier's change-control record.

Colour is a coarse signal. Off-white to cream covers a wide window, and a shade within it is not an identity failure. A clear darkening or a grey cast is worth a question about the drying step or the wheat source, even when protein and gluten both pass. Particle size moves with the mill and the sieve, so the 80 mesh result can change without any change in the chemistry.

Across lots, direction matters more than a single result: protein drifting toward the floor, moisture climbing with the season, or ash rising after a source change. The lot code on the certificate should match the pouch, the drum and the retained sample.

When an outside laboratory helps

An independent test is worth ordering for a new source or crop year, a first shipment into a regulated market, a disputed vitality result or a gluten-free claim that depends on the finished product. The panel should target the decision rather than repeat the whole certificate.

For identity, ask for Kjeldahl with the factor and the moisture, a named gluten method, a protein profile by SDS-PAGE or HPLC, ash and an ICP-MS metal panel. For a wheat-free or gluten-free statement, add a validated gliadin ELISA and report its limit of detection; a “not detected” line without a limit says more about the method than about the sample. Heat-treated and hydrolysed wheat proteins can read low in a sandwich ELISA, so the method has to be fit for the matrix.

If a result is challenged, send the referee the retained sample, the certificate and the specification, and ask for the test that separates the disputed property rather than a repeat of the same assay.

Comparing suppliers line by line

Seven items belong in a side-by-side comparison: wheat source and crop year; grade, meaning vital or devitalized; protein result with factor and basis; gluten result with method; moisture and ash; particle size; and the allergen statement.

The catalog specification is on the wheat gluten product page. The tests that separate gluten from starch and from other proteins are on the identity page; the grade and vitality question is on the grades page; the hydrolysed alternative is compared on the wheat protein peptides page; the protein methods are described in the methods library; and the release workflow is on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation