06 Identity & adulteration

How we prove a wheat gluten lot is wheat gluten

Technical document 06 · Reviewed 2026-11-20 · Wheat Gluten

On this page
  1. The five identity layers
  2. The nitrogen factor and the ratios that expose a blend
  3. X-ray diffraction: a filler screen, not an identity test
  4. How a substitution shows up
  5. Writing identity into the specification
  6. Five questions to ask the supplier

A wheat gluten lot is identified by a chain of agreeing measurements. The document names the material, the grade and the source; Kjeldahl nitrogen with the factor and basis gives the protein; a named gluten method gives the gluten figure; a protein profile shows the wheat storage proteins; and the mass balance leaves no room for starch or mineral filler. No single number proves identity, because a blend can be built to meet a protein target. The catalog specification is wheat gluten at ≥75.0% protein by N × 5.7 on the dry basis.

In one line

Identity is a chain of agreeing measurements: nitrogen by the stated factor, a gluten method that names its basis, a protein profile and a mass balance that leaves no room for starch.

The five identity layers

A certificate may name the right material without proving it. The layers below ask separate questions, and each needs its own evidence. A supplier who answers only the first has described paperwork, not powder.

Five layers of wheat gluten identity
LayerQuestionTestWhat it proves
DocumentAre the material and grade named?Name, CAS 8002-80-0, wheat source, vital or devitalizedPaperwork only
NitrogenHow much protein is present?Kjeldahl, N × 5.7, dry basisThe protein figure, not the source
GlutenHow much gluten, and is it vital?Named washing or gluten-index method; vitality testThe gluten fraction and its function
ProfileIs it wheat?SDS-PAGE or HPLC protein profile; amino acid patternThe wheat storage-protein family
BalanceIs it diluted?Moisture, ash, starch, mass balanceConsistency of the numbers

The nitrogen factor and the ratios that expose a blend

The nitrogen factor is a convention. This catalog uses 5.7; Codex Standard 163-1987 uses 6.25 for wheat gluten. The same result restated with the other factor is 75.0 × 6.25 ÷ 5.7 = about 82.2%. A supplier who reports 82% with the Codex factor and a supplier who reports 75% with the catalog factor may be describing the same powder, so the factor has to travel with the number.

The protein-to-gluten ratio is a second check. At 75.0% protein and 75.0% gluten the ratio is 1.0, which is what an intact wheat gluten should show when both lines use the same basis and a comparable method. A gluten figure well below the protein figure can mean a different method, a non-gluten protein fraction or a blend. The two lines should be read together, and neither should be copied from the other.

The dry-basis correction is the third ratio. A lot at 78.0% protein as received with 7.0% moisture is 83.9% dry basis; 75.0% dry basis at 8.0% moisture is 69.0% as received. A blend with 20% wheat starch would pull a 75.0% protein down to 60.0%, and the starch would also show in the mass balance and in the iodine test. The arithmetic is simple, and it catches the common dilution before a laboratory is booked.

X-ray diffraction: a filler screen, not an identity test

Wheat gluten is largely amorphous, so X-ray diffraction does not produce a fingerprint pattern that proves the protein. A diffractogram with sharp crystalline peaks is telling the reader about something else in the powder: crystalline starch, a mineral filler or a salt. That makes XRD a useful screen for adulteration and a poor release test for identity.

If a supplier offers “XRD conforms”, ask for the reference pattern and the detection limit. For wheat starch, the crystalline A-type pattern is a recognisable signal; for an amorphous protein, the absence of peaks is the expected result. XRD plus microscopy and an iodine test is a stronger check on starch than XRD alone. It is not a substitute for the protein profile.

How a substitution shows up

Common wheat gluten substitutions and the signals
AdulterantWhat it doesSignalTest
Wheat starchLowers protein; changes textureProtein and gluten low; starch highMass balance, iodine, XRD, microscopy
Lower-protein flourDilutes protein; adds starch and ashProtein near the floor; ash upProtein, ash, starch
Devitalized gluten sold as vitalProtein passes; dough function failsWeak or short hydrated massVitality or wet-gluten test, test bake
Soy or pea proteinRaises protein; changes amino acidsLysine up; profile differsAmino acid analysis, SDS-PAGE, ELISA
MoistureLowers the as-received proteinMoisture above the limitLoss on drying
Mineral fillerRaises ash; adds crystalline peaksAsh above 1.0%Ash, XRD, ICP-MS

Colour is the weakest signal. Off-white to cream covers a wide range, and a blend can match it. The stronger signals are the protein-to-gluten relationship, the amino acid pattern, the vitality test and the mass balance. A certificate that reports appearance and protein but no profile has left the most likely substitution untested.

Writing identity into the specification

  • “Wheat gluten, grade named as vital or devitalized, CAS 8002-80-0; wheat source and crop year declared.”
  • “Protein ≥75.0% by Kjeldahl, N × 5.7, on the dry basis; report moisture beside it.”
  • “Gluten content ≥75.0% by the named method, with the basis.”
  • “Identification by protein profile (SDS-PAGE or HPLC) against a reference.”
  • “Moisture ≤8.0%; ash ≤1.0%; particle size ≥95% through 80 mesh.”
  • “Vitality test by the agreed method where dough function is claimed.”
  • “Allergen statement: contains wheat and gluten; no gluten-free claim.”

Five questions to ask the supplier

  1. Is this lot vital or devitalized, and which wheat source and crop year does it come from?
  2. What nitrogen factor and basis were used, and what is the moisture result?
  3. Which gluten method was used, and what is the gluten result on the same basis?
  4. Can you provide the protein profile and the amino acid pattern, not only the protein percentage?
  5. If dough function is claimed, what vitality result supports it, and will you accept a joint re-test on the retained sample?

Those answers, taken together, form the identity file; one protein percentage cannot. The catalog values are on the wheat gluten product page; the COA page shows where each figure belongs; the grades page explains vitality; the wheat protein peptides page covers the hydrolysed alternative; the methods library and the quality page describe the analytical and release work.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation