02 Grade comparison

Walnut protein peptide grades: peptide, mesh and source

Technical document 02 · Reviewed 2026-11-19 · Walnut Protein Peptides

On this page
  1. Why a walnut peptide grade is a specification
  2. The catalog grade and the variants that need a new specification
  3. Flow, dust, colour and solubility
  4. What the grade means in a capsule, tablet or blend
  5. What to write into the specification

Walnut protein peptides are sold here as one catalog grade: an off-white to light tan powder at ≥80.0% protein by Kjeldahl, ≥70.0% peptide by HPLC, ash ≤5.0%, moisture ≤7.0% and ≥95% through 80 mesh. The grade questions that remain are the walnut fraction, the peptide window, the mesh and whether the powder is granulated. Those four change flow, dust, solubility and the label more than a different trade name does.

In one line

A walnut peptide grade is a set of numbers and a named source, not a trade name: the peptide window, the mesh and the walnut fraction decide how the powder runs and what the label can say.

Why a walnut peptide grade is a specification

“Walnut peptide” describes a family, not a single powder. Two suppliers can use the same name for hydrolysates made from different walnut materials, broken down to different degrees, decolourised on different lines and milled to different meshes. The protein figure can agree while the peptide distribution, the ash and the flow behave differently.

The starting material is usually defatted walnut meal, the press cake left after walnut oil is extracted. That meal is not a pure protein: it carries fibre, minerals and some residual oil, and the ratio of those components depends on the pressing and extraction route. A peptide made from a lightly pressed meal is not the same powder as one made from a thoroughly defatted meal, even when both are called walnut peptide.

On this page the catalog grade is fixed at five lines: protein ≥80.0%, peptide ≥70.0%, ash ≤5.0%, moisture ≤7.0% and ≥95% through 80 mesh. A change to any one is a new specification, not a packing choice. Juglans regia is the usual commercial walnut, but the fraction that goes into hydrolysis can be whole-kernel meal, a press cake or a blend, and the amino acid pattern and colour can differ.

The catalog grade and the variants that need a new specification

Walnut protein peptide forms and what changes
FormWhat changesWhy a buyer asks
80 mesh powderThe catalog grade; no changeCapsules, tablets and powder blends
Granulated, on requestLarger particles, less dust, slower wettingBlending and capsule feeding
Different meshDissolution rate, mouthfeel, sieve resultA tablet or a suspension needs a different particle size
Higher peptide fractionA different hydrolysis target and distributionA label or a formula calls for more short-chain material
Dilution or carrierLower peptide per gram; the label ingredient changesA lower potency is easier to weigh
Walnut protein, intactNot a hydrolysate; different solubility and labelA protein claim, not a peptide claim

The third and fourth rows are often confused. A finer or coarser mesh is a milling change; the chemistry stays the same. A higher peptide figure is a hydrolysis change. A dilution adds a carrier and changes what the label declares. If a supplier offers “walnut peptide 80%” and “walnut peptide 90%”, ask whether the second figure is protein, peptide or a dilution.

Granulation changes the particle size and flow without changing the protein or peptide figure, but it does change the mesh result and the way the powder wets out. A granulated grade is a different specification line even when the chemistry is identical.

The last row catches label errors. Intact walnut protein is a protein ingredient; walnut peptides are a hydrolysate with different solubility, taste and peptide figure. A switch changes the ingredient, not only the grade. A dilution or a different source is not a grade; it is a different purchase.

Flow, dust, colour and solubility

An 80 mesh powder passes about 177 µm. It flows reasonably in a capsule machine but dusts when poured, and dust can segregate in a blend or settle on equipment. Granulation binds the fines into larger particles, reducing dust and improving flow; the trade-off is slower wetting and a different particle-size result.

The catalog appearance is off-white to light tan. Colour moves with the walnut material, the decolourisation step and the drying temperature, and a tan shift inside the range is not a grade failure. The odour is mild and nutty; both matter in a capsule or plain blend, where no flavour system covers them.

Solubility is a grade question as well as a process question. The powder is soluble in water and gives a clear to slightly turbid solution. A cloudy solution can come from undissolved fines, a less hydrolysed fraction or a high mineral load; identify the cause before blaming the grade. Test it in the matrix at the concentration the formula will use, not only in water at 1%.

Hygroscopicity is the handling property that decides the pack. The 80 mesh powder has more surface area than a granulated grade and picks up moisture faster when a pouch is left open. A granulated grade is still hygroscopic, not a moisture barrier.

What the grade means in a capsule, tablet or blend

A capsule takes the 80 mesh powder directly. The fill weight is set by bulk density and the target peptide amount, and the shell needs a dry room because the powder pulls moisture from the air. A granulated grade can improve flow on a high-speed machine, but it changes the fill weight for the same volume and the label dose has to be recalculated.

A tablet needs flow and compressibility. A fine, hygroscopic powder can bridge in the hopper or cap during compression, and granulation is the usual answer; it is a formulation decision, not a cosmetic one. A blend takes the grade that matches the other ingredients in particle size, so it does not segregate. A stick pack takes the grade that disperses in the stated volume, and the mild nutty odour has to be acceptable.

The allergen is part of the dosage decision. A walnut peptide carries a tree-nut declaration into every format, so a capsule, a tablet and a blend all inherit the same label obligation. The grade cannot be selected to avoid that obligation; only a different source can.

What to write into the specification

  • “Walnut protein peptides, source Juglans regia; state the walnut fraction and the hydrolysis route.”
  • “Protein ≥80.0% by Kjeldahl; state the nitrogen factor and whether the figure is as-is or dry basis.”
  • “Peptide content ≥70.0% by HPLC; state the molecular-weight window and the integration method.”
  • “Ash ≤5.0%; moisture ≤7.0%; appearance off-white to light tan.”
  • “Particle size ≥95% through 80 mesh; granulated on request as a separate line.”
  • “Tree-nut allergen statement naming walnut; heavy metals and microbiology as agreed for the destination.”

A specification that lists only “walnut peptide 80%” has left the peptide, the mesh and the source open. The product hub carries the catalog values; the COA page shows how each line is reported; the walnut versus soy comparison covers the source question; the HPLC method note explains the peptide distribution; the quality page describes the release file.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation