06 Identity & adulteration

How to prove a lot is soy protein peptides

Technical document 06 · Reviewed 2026-11-19 · Soy Protein Peptides

On this page
  1. The five identity layers
  2. The peptide-to-protein ratio and the ash ratio
  3. Where XRD and FTIR stop
  4. What adulteration looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A soy protein peptide lot is identified by measurements that agree: the document names soy and the hydrolysis, protein by Kjeldahl, peptide content and distribution by HPLC, ash and moisture closing the mass balance, and a soy statement that matches the source. A protein percentage alone can be met by soy isolate, another plant protein or non-protein nitrogen, so it proves neither the hydrolysis nor the source.

In one line

Identity is the agreement of the source statement, the peptide distribution, the nitrogen figure and the mass balance; a protein percentage alone proves none of them.

The five identity layers

A name on a certificate is only a claim until a measurement backs it. Each layer below asks a different question and needs its own result; a supplier who supplies only a protein figure has not described the powder.

Five layers of soy protein peptide identity
LayerWhat it asksMethodWhat it establishes
DocumentAre soy and the hydrolysis named?Name, source, process descriptionPaperwork only
ProteinHow much nitrogenous material is present?Kjeldahl with the factor statedQuantity, not the source
PeptideIs the protein actually hydrolysed?HPLC distribution with the cut-off statedThe peptide fraction
Mass balanceIs the powder diluted?Moisture, ash and amino acid profileConsistency of the numbers
AllergenIs soy declared?Source-based allergen statementThe label obligation

The layers are independent. A lot can be genuine soy and still be diluted; it can pass protein and peptide and still carry another plant protein; it can be the right source and the wrong hydrolysis. Each needs its own evidence, and the evidence belongs in the batch file rather than in a marketing sentence.

The peptide-to-protein ratio and the ash ratio

The simplest screen is the ratio between the two headline figures. At 90.0% protein and 80.0% peptide on the same basis, the peptide fraction is 88.9% of the protein; the remaining 11.1 points are free amino acids, peptides below the HPLC cut-off and non-protein nitrogen. A wider gap points to a different hydrolysis, a different method or an addition.

The ratio also catches the common substitutions. Adding free amino acids raises the Kjeldahl figure while the peptide figure stays flat, so the ratio falls. Selling soy isolate as a peptide raises protein and leaves the peptide fraction low, so the ratio falls further. Diluting with a carrier lowers both figures, so the ratio can look normal while the absolute numbers drop.

Ash is a second ratio. At ≤5.0% ash and ≥90.0% protein, the ash-to-protein ratio is at most 0.056. A lot with 90% protein and 8% ash carries either a mineral load or a neutralisation salt that the specification did not intend. Moisture and ash must be converted to the same basis before the mass balance is closed; a dry-basis protein figure added to an as-is moisture figure will not add up.

Where XRD and FTIR stop

Spray-dried soy peptide has no crystal lattice, so an X-ray diffraction scan returns a broad halo instead of sharp peaks. That is what an amorphous hydrolysate should look like, but the halo says nothing about soy and nothing about hydrolysis. Sharp reflections point to something crystalline: a free amino acid, an inorganic salt, a mineral carrier or sugar that crystallised in storage.

XRD is not part of the routine release panel here. When a supplier reports “XRD conforms”, ask for the pattern, the reference and the question the test was meant to answer. FTIR is quicker: amide I near 1650 cm⁻¹ and amide II near 1545 cm⁻¹ show the peptide backbone. It confirms the material class, not the source, and cannot separate soy from pea or wheat.

What adulteration looks like

Substitution routes for soy protein peptides and the signals
RouteWhat it changesSignalTest
Soy isolate or another intact proteinProtein high, peptide lowPeptide-to-protein ratio low; opaque dispersionPeptide HPLC; solubility
Another plant proteinProtein passes, source is not soyAmino acid profile shift; soy marker absentAmino acid profile; PCR for soy
Free amino acidsProtein up, peptide flatPeptide-to-protein ratio lowPeptide HPLC; amino acid profile
Non-protein nitrogenKjeldahl up, peptide flatAmino acid sum short of the protein figureAmino acid profile; melamine by LC-MS/MS
Maltodextrin or carrierBoth headline figures downAsh, moisture and mass balance shiftMass balance; sugar HPLC

A PCR test for soy targets DNA, and a highly purified protein can carry little of it, so a negative result supports the file rather than proving absence on its own. The allergen declaration does not depend on the PCR result.

Colour proves the least. Off-white to light yellow is a wide window, and a carrier can be milled to match it. The peptide distribution, the amino acid profile and the mass balance carry the real evidence. For soy there is a second control: the allergen statement. A lot sold as soy peptide must carry the soy declaration, and an offer to remove it because the material is hydrolysed gets the obligation backwards.

How to write identity into the specification

  • “Hydrolysed soy protein, sold as soy protein peptides, with the soy source named.”
  • “Protein: ≥90.0% by Kjeldahl; the factor and the moisture basis appear on the COA.”
  • “Peptide: ≥80.0% by HPLC; column, mobile phase and cut-off named.”
  • “Moisture ≤7.0%, ash ≤5.0%, ≥95% passing 80 mesh.”
  • “Amino acid profile and molecular-weight distribution available on request.”
  • “No added plant protein, free amino acids, non-protein nitrogen or carrier.”
  • “Soy allergen statement; non-GMO or identity-preserved status only where claimed.”

Five questions for the supplier

  1. Which soy material went into the hydrolysis, and what enzyme, time and temperature were used?
  2. What factor and moisture basis sit behind the protein figure?
  3. Which HPLC method and cut-off produced the peptide figure, and can you send the distribution?
  4. What is the amino acid profile, and how does its sum compare with Kjeldahl?
  5. What does the soy allergen statement say, and will you support a joint re-test on the retained sample?

Five direct answers amount to an identity file. A single protein percentage does not. The product hub carries the catalog grade; the COA page shows where each figure sits on the certificate; the grades page compares the peptide and the isolate; the level-four comparison covers the label consequences; the methods section explains what each assay proves.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation