Soy isolate vs concentrate: protein, fiber and the label
Soy protein isolate and soy protein concentrate come from the same bean, but they leave the process at different points. The isolate is 90% protein or more on a dry basis and the concentrate is 65% to below 90%; the gap is mostly fiber, ash and carbohydrate. The choice changes the powder weight per serving, the texture and the ingredient name on the label, and it does not change the soy allergen.
Isolate and concentrate are different label ingredients: the isolate concentrates protein and leaves the fiber behind, while the concentrate keeps the fiber, ash and carbohydrate that the isolate washes out.
The protein figures and the factor behind them
The Codex standard for soy protein products sets the bands on a dry basis with N × 6.25: concentrate from 65% up to but not including 90%, isolate at 90% or more. The number is a floor, not a measurement. A lot at the floor and one well above it are both “isolate”, and the certificate has to report the actual result.
Moisture lowers both figures: at the 7.0% ceiling, the isolate reads 83.7% as-is and the 65% concentrate reads 60.5%. A serving calculation must use those lower numbers, because the powder on the bench contains water. Using the dry-basis figure on the powder weight overstates the serving by about six points.
The factor is the other half of the arithmetic. If a certificate uses the older 5.71 factor instead of 6.25, the same nitrogen reads about eight points lower: a true 90.0% isolate shows about 82.2%. The grade has not changed; the convention has. Name the factor and the basis before comparing the two grades.
Fiber, ash and the other fraction
| Point | Soy isolate | Soy concentrate | Why it matters |
|---|---|---|---|
| Protein, dry basis | ≥90.0% | 65% to below 90% | Powder needed per gram of protein |
| Fiber | Removed by the process | Retained from the bean | Carbohydrate declaration, texture, water binding |
| Ash | ≤5.0% (catalogue) | Usually higher; confirm the limit | Mineral load, taste, neutralisation |
| Fat | ≤1.0% (catalogue) | Usually higher; confirm the limit | Rancidity risk, mouthfeel |
Take the catalogue ceilings as a mass balance: once protein, ash and fat are counted, the isolate leaves roughly 4% of its dry matter for fiber and carbohydrate. A 65% concentrate leaves about 35% for those other components. In a bar, that difference becomes texture and water binding; in a drink, it becomes extra solids.
Alkaline extraction dissolves the protein; isoelectric precipitation separates it from the insoluble fiber; and washing carries the soluble sugars and part of the ash away. The concentrate process stops earlier: it washes out soluble sugars but leaves the fiber in the powder. They produce different ingredients.
What the difference takes in powder
The serving calculation starts from the as-is figure. Twenty grams of protein requires 23.9 g of the isolate at the floor, but 33.1 g of a 65% concentrate. The extra 9.2 g is not protein; it is the fiber, ash and carbohydrate that come with the lower grade. At 30 g of protein, the gap becomes 13.8 g.
| Protein target | Soy isolate | Soy concentrate | Extra powder |
|---|---|---|---|
| 20 g | 23.9 g | 33.1 g | 9.2 g |
| 30 g | 35.8 g | 49.6 g | 13.8 g |
Because the Codex band reaches almost to 90%, a high-protein concentrate closes part of the gap. At 70% protein, 20 g of protein takes 30.7 g of powder, not 33.1 g. Run the sum on the certificate for the lot, not on the bottom of the band. A scoop calibrated for the isolate underfills protein with concentrate, and a label that rounds the powder weight misstates the panel.
What each grade fits
For a stick pack or a drink mix, the isolate is usually the easier way to hit a 20 g protein claim without a 30 g powder fill. The isolate disperses to an opaque mixture; it does not form a clear solution, so neither grade is a clear-drink ingredient. Agglomerated or instantized isolate helps if wetting is the problem.
For a bar, the concentrate can be an advantage. Its fiber and non-protein fraction bind water and add body, and the bar matrix can absorb the extra powder. The isolate is the better fit when the bar is built around a high protein number per gram or when carbohydrate and fiber have a tight ceiling. For a capsule, the isolate's higher density means fewer capsules per dose.
Textured products want the concentrate for structure; fine blends and spoonable powders want the isolate for serving size and mouthfeel.
Ingredient names and the allergen
EU rules require the ingredient list to name the grade and to highlight the soy. A label might read “soy protein isolate (soy)” or “soy protein concentrate (soy)”, with soy emphasised in bold or capitals under Regulation (EU) No 1169/2011. US labelling uses the same grade names in the ingredient statement and a FALCPA declaration, either a parenthetical or a “Contains: soy” line. The UK keeps the same 14-allergen list in its retained law.
“Soy protein” alone does not identify the grade. If the product name says isolate, the ingredient statement cannot name a concentrate. Nor is the isolate a hypoallergenic form of soy: the protein remains soy protein and the allergen declaration is unchanged.
What the grade does not change
Both grades have a history of food use in Europe and are ordinary food ingredients in the US and the UK; as of this review, neither needs a novel food approval or a premarket authorisation because of its grade. Contaminant limits follow the finished product rather than the grade label, so a switch from concentrate to isolate leaves the applicable limit where it was.
Protein claims are calculated the same way for both. The EU's “source of protein” threshold is 12% of energy and “high protein” is 20% of energy; in the US, a “good source” claim sits at 10–19% of the Daily Value and “high” begins at 20%. Twenty grams of protein clears the EU “high” threshold in a 200 kcal drink but not in a 500 kcal one. The grade that supplied the protein does not alter that arithmetic, create a claim or remove the allergen.
Which grade fits which brief
Choose the isolate when the serving has no room for the extra grams, when protein per gram is the design constraint, when carbohydrate and fiber have a hard ceiling on the panel, or for a capsule or stick pack. Choose the concentrate when the fiber and the texture are part of the product, when the matrix is a bar or a textured application, and when the serving can absorb the extra powder without breaking the label.
Neither grade is a quality ranking. They are different ingredients with different protein density, fiber, ash and label names. The wider grade logic is on the grade comparison page; the numbers behind the certificate are on the COA page; the allergen and claims file is on the compliance page; and the catalogue specification is on the soy protein isolate page.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation