How we prove a micellar casein lot is micellar casein
Four independent questions decide whether a micellar casein lot is what the certificate calls it: whether the paper file names the process and the form, whether the protein and mineral results fit a micellar grade, whether the powder disperses like a micelle rather than dissolve like a caseinate, and whether the lot can be traced to the membrane and dryer that produced it. Protein alone answers none of them, because a caseinate or a blended milk powder can reach the same percentage. The four checks below are separate for that reason.
Identity is the agreement between the nitrogen figure, the mineral pattern, the way the powder disperses and the process that made it; no single line on the certificate carries that on its own.
The four identity layers
Each layer answers a different question and needs its own evidence. A supplier who provides only the first has documented an intention, not a powder.
| Layer | Question | Evidence | What it shows |
|---|---|---|---|
| Document | Are the form and process named? | Specification, CAS, site, lot | Intent and traceability only |
| Protein | Is the nitrogen a milk protein? | Kjeldahl with N × 6.38; amino acid profile | Protein quantity and pattern |
| Mineral | Is the milk mineral still there? | Ash, calcium and phosphorus by ICP-OES | The micellar mineral load |
| Behaviour | Does it disperse like a micelle? | Dispersion test at fixed shear and time | The form in the drum |
| Provenance | Can the lot be traced to the route? | Site and membrane record; retained sample | A process trail |
The ratios that carry the identity
Kjeldahl returns nitrogen, and the protein result is nitrogen multiplied by 6.38, expressed on a dry basis. The same powder reads differently at 6.0% and 9.0% moisture, and the same titration reads about 1.6 percentage points lower at 80% protein with the general factor of 6.25 than with 6.38. Both the factor and the basis therefore belong to the identity of the number.
The minerals are the second check. This grade allows up to 7.0% ash, part of which is the calcium phosphate associated with the micelle. Ask for calcium and phosphorus by ICP-OES beside the ash: a micellar grade carries both, sodium caseinate carries added sodium, calcium caseinate carries added calcium. Ash without the mineral panel cannot name a form.
The third check is the protein pattern. Milk contains roughly 80% casein and 20% whey protein; membrane processing removes much of the whey, so a micellar grade has a higher casein share. SDS-PAGE shows the casein and residual whey bands, and an amino acid profile distinguishes milk protein from plant protein. A powder at 80% protein with a strong whey band does not match the description.
X-ray diffraction: a screen, not an identity test
X-ray diffraction cannot prove the micelle. Casein is amorphous, so the pattern is a broad halo without crystalline peaks, and micellar casein and caseinate look alike. A supplier offering XRD as the identity test for casein is offering a test that cannot distinguish the forms.
It can still answer a different question. Sharp crystalline peaks indicate a crystalline ingredient — lactose, a mineral salt or crystalline dextrose — and therefore a blend or a diluted powder rather than a pure protein. That is a useful screen for dilution, not proof of the micelle. The methods library covers the technique, and the XRD note explains what a pattern can support.
What substitution looks like
| Route | Signal | Test |
|---|---|---|
| Caseinate substituted | Ash and sodium or calcium move; dispersion is faster | Ash, ICP-OES, dispersion test |
| Whey protein added | More whey bands; casein share drops; lactose can rise | SDS-PAGE, lactose by HPLC |
| Plant protein present | Amino profile not typical of milk; extra bands on the gel | Amino acid profile, SDS-PAGE |
| Nitrogen booster added | Kjeldahl high; the amino acid sum low | Kjeldahl, amino acid profile, melamine/cyanuric acid screen |
| Lower-protein milk solid | Lactose and ash both climb | Lactose, ash, protein on a dry basis |
| Crystalline carrier added | XRD shows crystalline peaks; ash or sugar rises | XRD, lactose, ash, mass balance |
Appearance is the weakest evidence. Off-white to cream covers many blends, and a formulator can match it. The mineral panel, the protein pattern and the dispersion test are harder to fake. A certificate that lists appearance and protein but no identity data leaves the most likely substitution unexamined.
How to write identity into the specification
- “Micellar casein, CAS 9000-71-9, separated from skim milk by microfiltration.”
- “Protein ≥80.0% on a dry basis by Kjeldahl, N × 6.38; factor and basis printed.”
- “Moisture ≤6.0%, fat ≤2.0%, lactose ≤1.0%, ash ≤7.0%.”
- “Calcium and phosphorus reported by ICP-OES; ash beside them.”
- “Dispersion test reporting grams per 100 mL, water temperature, shear, time and sediment limit.”
- “Allergen: milk declared; statement on the specification and the COA.”
- “Site, membrane route, lot code and retained sample named for every lot.”
Five questions for the supplier
- How was this lot made: microfiltration of skim milk, acid precipitation, or neutralisation of acid casein?
- What are the ash, calcium and phosphorus values, and what limits apply?
- Can you send the amino acid profile and the SDS-PAGE pattern for the lot?
- Which dispersion method do you use, and what result did this lot give?
- Which site produced the lot, and do the bag, COA and retained sample share a lot code?
Five answers of this kind amount to an identity file; a protein percentage on its own does not. The product hub lists the catalog specification, the COA page places each figure on the certificate, the grades page compares the forms, the casein page covers the 90% grade, and the quality page explains the retained-sample system.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation