Micellar casein vs casein: solubility, processing and the label
Micellar casein is casein that has kept the micelle it had in milk: the skim milk is filtered rather than acidified, so the calcium phosphate and the casein proteins stay together and the powder disperses without dissolving. “Casein” on its own is a family name — on this site the casein page carries a 90% micellar grade, this product is the 80% grade, and the caseinates are separate salts. The two micellar grades differ in protein per gram, ash and mineral load, dispersion behaviour and the ingredient name the label can carry.
Filtered, not precipitated: micellar casein keeps the micelle, disperses instead of dissolving, and carries more milk minerals than the 90% grade — the label has to name the form, not just “casein”.
Two micellar grades, and the family name around them
Casein is about 80% of the protein in cow’s milk and the fraction that curdles at pH 4.6. As a purchase order, “casein” can mean three different materials: micellar casein, acid casein and a caseinate. Micellar casein is made by microfiltration; acid casein is precipitated by lowering the pH; a caseinate is acid casein redissolved with sodium or calcium hydroxide. The three share a protein, not a powder.
This site lists two micellar grades. The 80% grade on this page keeps more of the milk’s mineral load and is specified with ash ≤7.0%; the 90% grade on the casein page carries ash ≤2.0%. Both are micellar casein, and neither is a caseinate. A buyer comparing them is comparing protein per gram and mineral load, not two chemical forms.
Filtration, precipitation and what the membrane leaves behind
The micellar route starts with skim milk and passes it across a membrane with pores around 0.1 µm. Casein micelles are between roughly 50 and 500 nm, so they are retained; whey proteins, lactose and soluble salts pass with the permeate. Diafiltration — adding water and repeating the concentration — washes more lactose and soluble mineral out and lifts the protein on a dry basis. The retentate is then spray-dried.
The acid route is different. Skim milk is acidified to pH 4.6, the casein curd is separated, washed and dried, and the result is acid casein: a material that does not disperse in water at its isoelectric point. A caseinate is made by redissolving that curd with sodium or calcium hydroxide and drying the solution. The salt dissolves because the protein has been taken apart and neutralised, not because the micelle survived.
The two micellar grades sit at different points on the same membrane route. The 90% grade has a lower ash ceiling and a higher moisture ceiling; the 80% grade keeps more of the milk minerals and is dried to ≤6.0% moisture. The two are separate specifications rather than one powder at two dilutions. Confirm the membrane and drying route on the certificate rather than inferring it from the protein number.
Dispersion is not solution
“Soluble” does not apply to micellar casein. In water the micelle hydrates and swells, the dispersion turns opaque and the viscosity rises; left standing, it settles. That behaviour gives body and mouthfeel, and it is why the powder needs shear and time rather than a brief stir.
Heat and acid both change the picture. A heat step thickens the dispersion and can gel it, so the process needs a trial at the real solids, pH and holding time. Near pH 4.6 the micelle loses its charge and the protein precipitates; an acidic drink is not a simple base for this material.
A sodium caseinate is freely soluble and gives a slightly turbid solution; a calcium caseinate disperses more readily than the micelle and carries its own calcium load. Acid casein does not disperse at all at its isoelectric point. Those differences are the practical reason the four names are not interchangeable in a mixer.
The numbers that change with the grade
| Property | Micellar casein 80% | Casein grade 90% | What it changes |
|---|---|---|---|
| Protein, dry basis | ≥80.0% | ≥90.0% | Protein per gram of powder |
| Ash | ≤7.0% | ≤2.0% | Mineral load in the formula |
| Fat | ≤2.0% | ≤1.5% | Energy and mouthfeel |
| Lactose | ≤1.0% | ≤1.0% | Browning and sugar declaration |
| Moisture | ≤6.0% | ≤10.0% | As-is protein and caking risk |
| Particle size | ≥95% through 80 mesh | ≥95% through 80 mesh | Flow, dust and fill weight |
| In water | Disperses; opaque; thickens | Disperses; opaque | Mixer, time and viscosity |
The protein line is on a dry basis in both grades, with N × 6.38. At 6.0% moisture the 80% figure is about 75.2% as weighed; the 90% grade at its 10.0% ceiling is about 81.0% as weighed. Comparing an as-is result from one with a dry-basis result from the other is the most common arithmetic error in a grade switch.
What the label and the allergen file have to say
The ingredient name follows the process. A micellar grade is declared as micellar casein or milk protein concentrate, depending on the market; a caseinate must be declared as sodium caseinate or calcium caseinate. A label that says “casein” for a caseinate has named the family, not the ingredient.
Milk is a major allergen in the EU and the US, and every one of these materials is a milk protein. The declaration is required whichever grade is used, and the lactose ceiling on this grade — ≤1.0% — does not make the powder dairy-free or non-allergenic. The specification and the COA carry the allergen statement; the finished-product label must carry the milk declaration, and the compliance page covers the market wording.
The protein declaration has its own basis problem. A label that declares the dry-basis protein per 100 g overstates what is in the powder as weighed. Use the as-is figure for the nutrition panel and keep the dry-basis figure for the specification.
Choosing between them
Choose the 80% micellar grade when the formula wants the milk minerals and the fuller body, and when the protein per gram can be lower. Choose the 90% grade when the protein per gram matters more and the lower ash ceiling fits the formula. Choose a caseinate when the powder has to dissolve, when the drink has to be near-clear, or when the process needs a heat-tolerant protein.
Do not switch grades to solve a supply problem without a trial: the dispersion, the viscosity, the fill weight and the label all move together. A grade change is a specification change, and it needs a new certificate, a new allergen statement and a fresh label review. The product hub carries the catalog range; the grades page compares all three forms; the identity page shows how the micelle is proved; the methods library describes the assays; the quality page describes the release file.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation