06 Identity & adulteration

How we prove a collagen peptide is collagen, and which species

Technical document 06 · Reviewed 2026-11-18 · Collagen Peptides

On this page
  1. The four layers
  2. The hydroxyproline-to-protein ratio
  3. The molecular weight distribution
  4. Why XRD is not the identity test here
  5. The adulteration routes
  6. What to write into the specification
  7. Questions to put to a supplier

Proving that a powder is a collagen peptide takes four separate answers: that it is protein, that the protein is collagen, that it has been hydrolysed to the declared size, and that it comes from the declared species and tissue. No single test covers all four, and a certificate that reports only the protein figure has answered the first question and skipped the other three.

In one line

Identity is four tests, not one: the amino acid profile, hydroxyproline, the molecular weight curve and the species, each answering a different question.

The four layers

The first layer is protein: the material is a peptide mixture, and its amino acid profile is dominated by glycine, proline and hydroxyproline. The second layer is collagen: hydroxyproline is the marker that separates a collagen hydrolysate from other proteins, because it is rare outside collagen. The third is the degree of hydrolysis: the molecular weight distribution shows how far the chains were cut. The fourth is the source: the species and the tissue, which the certificate declares and which can be checked by a DNA method.

The layers are independent. A lot can be genuine collagen and still be the wrong species; it can be the right species and over-hydrolysed for the intended label; it can be a fine peptide mixture and still carry non-collagen nitrogen. Each layer needs its own evidence, and the evidence belongs in the batch file rather than in a marketing sentence.

The hydroxyproline-to-protein ratio

Hydroxyproline is measured colorimetrically, and the result is compared with the protein figure. The catalogue range is 8.0–12.0% hydroxyproline at ≥90.0% protein, which is roughly 9–13 g of hydroxyproline per 100 g of protein. That ratio is the simplest identity check available, because it compares two numbers that are already on the certificate.

A high protein figure with a low hydroxyproline figure is the signal that matters. It means the nitrogen in the drum is not all coming from collagen. The extra nitrogen can come from another protein, from a non-protein nitrogen source, or from a collagen material that has been diluted with a nitrogen-rich carrier. The protein figure alone cannot tell those three apart; the ratio shows that something needs to be explained.

The reverse is less common but possible: a high hydroxyproline figure with a low protein figure suggests a material that has been blended with free amino acids or with a non-nitrogenous filler. The COA page sets out how the two figures are reported together.

The molecular weight distribution

The molecular weight distribution is measured by size-exclusion chromatography with an HPLC system, and the specification states the share of the mass below a cut-off: ≥90% below 3,000 Da for the catalogue grade. That single number is a gate, not a description. Two lots can both meet it while sitting at opposite ends of the distribution, and the difference shows up in solubility, in mouthfeel, in foam and in odour.

The distribution proves hydrolysis; it does not prove identity. A whey protein hydrolysate can also be measured by SEC-HPLC and can also be reported below a cut-off. What the method does is link the powder to the process that made it and to the behaviour the formulator is buying. Ask for the distribution by mass fraction, not only for the percentage under the cut-off, because the tail above the cut-off is what makes a clear drink hazy.

Why XRD is not the identity test here

Collagen peptides are amorphous. A diffraction scan of the powder gives a broad halo around 20° two-theta and no sharp reflections, and gelatin, a whey hydrolysate and a collagen peptide look much the same in that region. The method cannot separate collagen from another hydrolysed protein, measure the degree of hydrolysis or name the species. The detection limit for a crystalline minor phase is typically a few percent, and the peptide itself has no crystal lattice to read.

Where XRD earns a place is the screen for crystalline additions: sodium chloride, lactose or a crystalline mineral diluent returns sharp peaks that a peptide powder should not have. That is a check on the drum, not proof of identity. The identity evidence remains hydroxyproline, the amino acid profile, the SEC molecular weight curve and species PCR; the XRD method note sets out what a phase scan can and cannot establish.

The adulteration routes

Adulteration routes · what each one changes
RouteWhat it doesSignature
Gelatin or partly hydrolysed collagenRaises the protein figure with genuine collagenHigher molecular weight, gelling, slower dissolution
Other protein (whey, soy, pea)Raises the protein figure at lower costLower hydroxyproline, different amino acid profile
Non-protein nitrogenInflates Kjeldahl without adding proteinProtein up, hydroxyproline flat, amino acid profile short
Non-type-I collagen tissueSubstitutes bone or cartilage for hideTissue declaration, wider peptide curve, mineral load
Species substitutionPorcine or fish material sold as bovineSpecies PCR on the retained sample

Gelatin is the hardest route to see, because the material really is collagen. The difference is the degree of hydrolysis, and it is visible in the molecular weight curve and in the way the powder behaves in water. The other proteins are easier: they lower hydroxyproline and change the amino acid profile. Non-protein nitrogen is the case that most needs the hydroxyproline check, because it raises the protein figure without raising any amino acid.

What to write into the specification

  • “Hydrolysed collagen peptides, type I, bovine hide; species and tissue stated on the certificate.”
  • “Protein ≥90.0% dry basis by Kjeldahl with N × 5.55; factor and basis stated on the COA.”
  • “Hydroxyproline 8.0–12.0% by colorimetric method.”
  • “Molecular weight: ≥90% below 3,000 Da by SEC-HPLC; distribution reported by mass fraction.”
  • “Amino acid profile reported; no added non-collagen protein or non-protein nitrogen.”
  • “Species verified by PCR on request; retained sample kept for the shelf life of the lot.”

Questions to put to a supplier

  1. What is the hydroxyproline figure on this lot, and what is it as a share of the protein figure?
  2. Can you send the full molecular weight distribution, not only the percentage below the cut-off?
  3. Which species and which tissue does the certificate declare, and is there a PCR report?
  4. Does the lot contain any protein or nitrogen source other than the declared collagen?
  5. What retained sample is kept, and for how long after the lot is released?

For the tests behind these answers, see the COA page and the HPLC method note. The source decision is set out on fish versus bovine collagen peptides, and the regulatory file that the identity evidence supports is on the compliance page. The full range is on the product page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation