01 COA & batch testing

What the COA for collagen peptides actually contains

Technical document 01 · Reviewed 2026-11-18 · Collagen Peptides

On this page
  1. The parameter list
  2. What the protein figure is measured against
  3. Catalogue range, release limit and lot result
  4. What moves between lots
  5. When to send a sample to an outside laboratory
  6. What to compare between suppliers

A certificate for collagen peptides carries three figures that decide what the material is: the protein content with its nitrogen conversion factor, the hydroxyproline content, and the molecular weight distribution. Each figure is only meaningful beside its method and its basis. The catalogue specification sets the ranges; the batch COA confirms what the lot in the drum actually measured.

In one line

A collagen certificate is complete only when the protein factor, the hydroxyproline result and the molecular weight distribution appear together, each with its method.

The parameter list

Collagen peptides have no single CAS number, because the material is a mixture of peptides rather than one molecule. The certificate is therefore built on the parameters that describe the mixture: how much protein it carries, how much of that protein is collagen, how large the peptides are, and what else is in the drum. The table below is the catalogue parameter list; the release limits are agreed in the specification and repeated on every lot.

COA parameter list · collagen peptides, bovine hide type I
ParameterMethodRelease limit
AppearanceVisualWhite to off-white powder
Protein (dry basis)Kjeldahl, N × 5.55≥90.0%
HydroxyprolineColorimetric8.0–12.0%
Molecular weightSEC-HPLC≥90% below 3,000 Da
MoistureLoss on drying≤7.0%
AshGravimetric, furnace≤2.0%
pH (10% solution)Potentiometry5.0–7.0
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and enrichmentAPC ≤1,000 cfu/g · yeast and mould ≤100 cfu/g · E. coli and Salmonella absent

The source is a parameter too, even though it produces no number. The species and the tissue belong on the certificate and in the specification, because bovine hide, bovine bone, porcine skin and fish skin are different label ingredients. The identity page covers how that declaration is supported.

What the protein figure is measured against

Kjeldahl measures nitrogen, not protein. The nitrogen result is multiplied by a conversion factor, and the factor is a convention rather than a measurement. Collagen is calculated with N × 5.55 because its nitrogen content is close to 18% of the protein mass. A general food protein is calculated with N × 6.25, which assumes 16% nitrogen.

The same nitrogen result therefore produces two different protein figures. Because 6.25 is about 12% larger than 5.55, a lot that reads 90.0% under the collagen factor would read roughly 101% under the general factor. That second figure is not a richer material; it is the same powder with a different convention applied. A certificate that does not name the factor cannot be compared with one that does, and a specification that says only “protein ≥90%” leaves the arithmetic open.

The basis matters as much as the factor. The catalogue figure is on a dry basis. At the 7.0% moisture limit, a 90.0% dry-basis figure corresponds to about 83.7% on an as-is basis. Both statements describe the same powder, but a label or a purchase order that mixes the two bases will be wrong by several percent before any analytical variation is counted.

Catalogue range, release limit and lot result

A release limit is the window the lot must fall inside. A lot result is what the laboratory measured on that lot. A useful certificate shows both, with the method beside each line. “Conforms to specification” on its own is a conclusion without the evidence behind it.

Some parameters are reported rather than limited. The molecular weight distribution is the clearest case: the specification can require ≥90% of the mass below 3,000 Da, and the certificate can still report the measured distribution. A lot can meet the cut-off while sitting at the high end of it, and that difference shows up in solubility, in mouthfeel and in how the powder smells. The cut-off is a gate, not a description.

The specification described on this page is a catalogue specification. It states what the material is expected to meet; the batch COA confirms the lot that actually ships. No page on this site reports a batch result, a batch number or a customer, and none should be read as one.

What moves between lots

The protein and hydroxyproline figures follow the raw material and the hydrolysis step. Hide trimmings differ in composition from lot to lot, and the hydrolysis time and temperature decide how far the chains are cut. A longer hydrolysis lowers the average molecular weight and can slightly change the nitrogen recovery. Filtration and concentration decide how much of the fine fraction survives; drying decides the moisture and the colour.

Odour is the least quantitative signal and often the most useful. Collagen peptide powder can carry a faint broth or hide note that strengthens with moisture uptake and with storage temperature. The protein figure can still pass while the odour has moved outside what a flavoured beverage can mask. That is a reason to ask for the retained sample and the storage history, not a reason to reject the lot on the number alone.

When to send a sample to an outside laboratory

Order an independent test when the source is new, when the first commercial shipment is about to enter a regulated market, or when the label makes a statement the supplier's certificate does not prove. The useful panel is not a full repeat of the certificate. It is the set that answers the open question: hydroxyproline and the amino acid profile for collagen identity, SEC-HPLC for the molecular weight distribution, species-specific PCR for the declared source, and ICP-MS for the contaminant panel on the same sample.

An outside laboratory is also the right way to settle a dispute. Send the retained sample, the supplier's certificate and the agreed specification, and ask for the specific tests that separate the possible explanations rather than for the whole panel again. The quality page describes how the batch file and the retained sample are kept together.

What to compare between suppliers

Put six lines side by side before looking at anything else: the protein figure with its nitrogen factor and its basis, the hydroxyproline figure, the molecular weight distribution including the method, the moisture and ash limits, the species and tissue, and the allergen statement. If two quotations agree on the protein percentage but disagree on the other five, they are not quoting the same material.

The second layer is the record behind the certificate: which site made the lot, which raw material batch went in, which hydrolysis and drying conditions were applied, and what retained sample exists. A certificate can be accurate and still describe a lot other than the one that arrives. The lot number on the COA, on the drum and on the retained sample should be the same number.

For the ranges themselves, see the collagen peptides product page. The grade decision is on the grade comparison page, the tests that prove collagen identity are on the identity page, and the definition of the certificate is in the COA glossary entry.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation