06 Identity & adulteration

How we prove a sodium citrate lot is the trisodium dihydrate

Technical document 06 · Reviewed 2026-11-19 · Sodium Citrate

On this page
  1. Five layers of identity
  2. The sodium-to-citrate ratio
  3. X-ray diffraction and the solid state
  4. What adulteration looks like
  5. Writing identity into the specification
  6. Questions that expose the form

A sodium citrate lot is trisodium citrate dihydrate when five measurements agree: the document names the hydrate and the CAS number, the infrared spectrum matches the reference and the citrate reaction is positive, the sodium figure sits near 23.45%, the water result sits near 12.25%, and the titration gives 99.0–100.5% on the anhydrous basis. The assay alone cannot separate the dihydrate from the anhydrous salt, from disodium citrate, or from a blend with sodium chloride. The sodium-to-citrate ratio is the measurement that can.

In one line

Three sodium ions per citrate set the identity: 23.45% sodium, 64.3% citrate and 12.25% water is one salt, and a departure from that ratio points to a different cation count or an added salt.

Five layers of identity

Each layer answers a different question, and a supplier who answers only the first has described the paperwork rather than the powder. The order matters: the document says what the lot is claimed to be, the spectrum says the anion, the sodium says the cation count, the water says the hydrate, and the mass balance says whether the numbers describe one material.

Five layers of sodium citrate dihydrate identity
LayerThe question it answersTestEvidence it gives
DocumentIs the hydrate named?Name, CAS number, formulaPaperwork only
CitrateIs the anion citrate?Infrared spectrum; citrate reactionThe anion, not the cation
SodiumIs it the trisodium salt?Sodium by ICP-OES, or calculated from the assayThe cation count
WaterIs it the dihydrate?Karl FischerThe hydrate state
Mass balanceDoes it add up?Assay, sodium, water, chlorideDilution and added salts

The sodium-to-citrate ratio

Trisodium citrate has three sodium ions for one citrate anion. In the dihydrate that is 68.97 g of sodium and 189.10 g of citrate in 294.10 g of salt, or 23.45% sodium, 64.30% citrate and 12.25% water. Convert a result to moles per 100 g and the ratio should come out near 3.00. A lot at 23.3% sodium and 64.0% citrate gives 1.0135 mol of sodium and 0.3384 mol of citrate, a ratio of 2.99.

The ratio is what separates the neighbouring salts. Disodium citrate carries two sodium per citrate, about 19.47% sodium in the anhydrous salt, and a ratio near 2. Monosodium citrate carries one, about 10.74%, and a ratio near 1. Both are legitimate articles with their own CAS numbers; neither is the trisodium salt, and a certificate that reports only “citrate” will not tell them apart.

Added salts move the ratio in the other direction. A blend of 90% dihydrate and 10% sodium chloride reports about 25.0% sodium, 57.9% citrate and a ratio near 3.56, and the chloride line confirms it. Added citric acid reports more citrate and less sodium, a ratio below 3.0, and a lower solution pH. An inert diluent leaves the ratio at 3.0 and lowers the assay, which is why the ratio and the mass balance are read together.

X-ray diffraction and the solid state

X-ray diffraction reads the crystal rather than the solution. The dihydrate has its own pattern, the anhydrous salt has a different one, and the scan therefore settles a hydrate dispute that a water result alone can only suggest. It also shows a crystalline second phase: sodium chloride as halite gives strong reflections near 31.7° and 45.4° two-theta with copper radiation, well clear of the citrate pattern.

XRD is not a release test for this product. Use it when the hydrate state is disputed, when a supplier changes its drying step, or when a crystalline chloride or carbonate is suspected. Ask for the reference pattern the lot was compared against and for the detection limit; a scan reported as “matches” without either is a statement, not a result. An amorphous spray-dried material will not give sharp reflections at all, which is itself useful information.

What adulteration looks like

Common sodium citrate substitutions and the signals
SubstituteEffect on the lotWhat shows itTest
Sodium chlorideCommon sodium salt; no citrateRatio above 3.0; chloride present; salty tasteChloride by titration or IC; sodium
Citric acidAdds citrate; removes sodiumRatio below 3.0; pH fallsSodium and citrate; pH
Disodium or monosodium citrateLower cation count; lower pHRatio near 2 or 1Sodium; pH; XRD
Dextrose or maltodextrinDilution; assay fallsRatio near 3.0; assay lowAssay; reducing-sugar test; XRD
WaterDilutes the as-is assayKarl Fischer above 13.0%Karl Fischer; anhydrous assay
Sodium bicarbonateRaises sodium and pHEffervescence in acid; ratio above 3.0Acid test; XRD; sodium

Colour and appearance are the weakest signals: a white crystalline powder is easy to match. The stronger evidence is the ratio, the chloride line and the water result, read together. A certificate that reports appearance and assay but no sodium or chloride figure leaves the likeliest substitution unexamined.

Writing identity into the specification

  • “Trisodium citrate dihydrate, C6H5Na3O7·2H2O, CAS 6132-04-3.”
  • “Assay 99.0–100.5% by titration on the anhydrous basis; water 11.0–13.0% by Karl Fischer.”
  • “Sodium 22.5–24.0% as weighed; report the sodium:citrate ratio where the form is in question.”
  • “Identification by infrared spectrum against a reference, plus the citrate reaction.”
  • “Chloride limit stated, with the method, where the route or the customer sets one.”
  • “No added sodium chloride, citric acid or other citrate salt.”

Questions that expose the form

  1. Which hydrate is on the certificate, and what water result and method does it report?
  2. What sodium figure is reported, and was it measured or calculated?
  3. Can you send the infrared spectrum, with the reference it was matched to?
  4. Does the sodium:citrate ratio agree with the trisodium salt, and can you show the working?
  5. Is any chloride, other citrate salt or diluent present, and what backs that answer?

Five straight answers are an identity file; a single assay figure is not. Catalog ranges are published on the product hub, and the COA page places each figure on the certificate. The grades page compares the hydrate states, the chloride comparison covers the substitution that the ratio detects, and the methods library describes the spectra and the titration.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation