06 Identity & adulteration

How we prove a lot is potassium chloride

Technical document 06 · Reviewed 2026-11-20 · Potassium Chloride

On this page
  1. The identity layers
  2. The 1:1 ratio and the mass balance
  3. X-ray diffraction: the solid-state check
  4. What adulteration looks like
  5. How to write the identity into the specification
  6. Five questions for the supplier

A potassium chloride lot is the named material when the document, the potassium figure, the chloride figure and the solid-state pattern agree. The theoretical composition is 52.45% potassium and 47.55% chloride, a 1:1 molar ratio; the potassium line by flame photometry and the chloride line by titration or ion chromatography should land on that ratio. Sodium is the substitution to screen for, because sodium chloride is white, salty and cheap. One assay percentage cannot separate the salt from a sodium chloride blend.

In one line

Identity is the potassium and the chloride agreeing on the same lot, with the 1:1 ratio and the diffraction pattern separating potassium chloride from sodium chloride.

The identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Layers of potassium chloride identity
LayerQuestionTestWhat it proves
DocumentIs the salt named?Name, CAS number, formulaPaperwork only
PotassiumHow much potassium?Flame photometry or ICP-OESThe element, not the salt
ChlorideIs the counter-ion chloride?Argentometric titration or ion chromatographyThe anion
RatioDo the two figures agree?Potassium and chloride on the same lotConsistency of the salt
Solid stateWhich crystalline phases are present?X-ray diffractionPotassium chloride against sodium chloride

The first layer is necessary and quick. The next four are analytical, and they have to be run on the same lot. A potassium figure from one batch and a chloride figure from another describe a hypothetical material, not a drum.

The 1:1 ratio and the mass balance

Potassium chloride is KCl: one potassium and one chloride. On the theoretical formula that is 52.45% potassium and 47.55% chloride, a mass ratio of 1.103. Those two figures are the identity arithmetic, and they should be consistent on the same certificate. The two lines are the identity arithmetic; the ratio says whether they belong together.

The ratio catches the common substitutions. If sodium chloride is blended in, potassium falls and chloride stays high relative to it, and sodium appears. A 10% sodium chloride addition moves potassium down by about five points and leaves chloride near 49%, so the potassium-to-chloride ratio falls from 1.10 to about 0.97. If potassium sulfate or carbonate is added, chloride falls against potassium and the ratio rises. Neither substitution is visible in a single assay percentage, which is why the two lines have to be read together.

The assay basis is a separate question. Potassium chloride has no water of crystallisation, so the loss on drying is surface moisture and the dried-basis correction is small, but it is not zero. A 100.0% result on the dried basis at 0.5% water is 99.5% of the powder as weighed. The certificate should state the basis and the loss on drying, and the identity arithmetic should use the same basis for both elements. The COA page sets out that correction.

The ratio also catches a physical blend that was built to pass the assay. A powder made from potassium chloride and a little sodium chloride can be adjusted to land inside the assay range, but its potassium figure falls and its sodium figure rises. The chloride titration sees total chloride; the potassium line sees the element.

X-ray diffraction: the solid-state check

Potassium chloride crystallises in the rock-salt structure, the same cubic arrangement as sodium chloride, but the two have different lattice spacings. The diffraction peaks therefore sit at different angles, and a pattern can show sodium chloride as a second crystalline phase beside the potassium chloride. That is a different question from the wet chemistry: the ratio infers a blend from two numbers, while diffraction looks at the phases in the powder.

XRD is not a purity assay. It sees crystalline phases above its detection limit, not amorphous material, not a thin coating and not an organic adulterant that is present in small amounts. The sample preparation changes what the pattern represents, and a “match” statement without the reference pattern and the detection limit adds little. Ask for the reference, the limit and the preparation method before reading the conclusion. The methods index explains what the technique can and cannot see.

For a disputed lot, XRD plus potassium plus chloride plus sodium is stronger than any one of them. XRD is not a routine release test for this salt, and a certificate that reports only “XRD conforms” has not shown the pattern.

What adulteration looks like

Common potassium chloride substitutions and the signals
AdulterantWhat it doesSignalTest
Sodium chlorideCheap, white and salty; lowers potassium per gramPotassium low; chloride high against it; sodium presentPotassium, chloride, sodium by ICP-OES, XRD
Potassium sulfateWhite; adds potassium and sulfate, no chlorideChloride low against potassium; sulfate presentIon chromatography, XRD
Potassium carbonateWhite; alkaline solution; no chlorideChloride low; pH high; carbonate presentpH, titrimetric carbonate, XRD
Potassium citrateWhite; adds potassium and organic anionChloride low; citrate reaction; pH highCitrate test, ion chromatography, pH
WaterSurface moisture; caking and weight gainLoss on drying above 0.5%; pouch weight gainLoss on drying, weight gain

Colour is the weakest signal on a white salt, and a small addition of sodium chloride changes nothing visible. The stronger signals are the potassium-to-chloride ratio, the sodium result, the pH and the diffraction pattern. A certificate that reports appearance and assay but not potassium and chloride has left the most likely substitution untested.

How to write the identity into the specification

  • “Potassium chloride, CAS 7447-40-7, KCl, food or supplement grade.”
  • “Assay 99.0–101.0% by titration, with the basis stated.”
  • “Potassium 52.0–55.0% by flame photometry; report the method and the standard.”
  • “Chloride reported against the theoretical 47.55%.”
  • “Identification by potassium flame test and chloride precipitation.”
  • “Sodium reported where the source is sylvinite; no added sodium chloride.”
  • “XRD reference pattern and detection limit stated where the solid form is tested.”
  • “Particle size ≥95% through 80 mesh; heavy metals and microbiology as listed.”

Five questions for the supplier

  1. What are the potassium and chloride figures on this lot, by which methods, and on which basis?
  2. What is the sodium result, and was it measured by flame photometry or ICP-OES?
  3. Can you provide the titration record and the flame-photometry calibration, not only the assay percentage?
  4. Is there an XRD pattern, and what reference and detection limit does it state?
  5. If the lot is disputed, will you accept a joint re-test on the retained sample?

Five answers make an identity file; one assay percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grades page compares the mesh and the granulation; the potassium citrate page shows a different anion with its own ratio; the quality page describes the retained-sample workflow.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation