What the COA for iron pyrophosphate actually contains
The certificate for a ferric pyrophosphate lot reports appearance, iron by ICP-OES, identification reactions for iron and pyrophosphate, loss on drying, particle size, bulk density, heavy metals and microbiology. Each line should show the method and the release limit, and every result should belong to the lot named at the top. The catalog window is 24.0–26.0% elemental iron; the batch COA confirms a particular drum. An iron figure alone does not separate the ferric salt from a ferrous source or an iron oxide.
An iron result of 24.0–26.0% says how much iron is in the drum, not which iron salt holds it.
The certificate as a test report
A certificate earns its place when every line can be checked. For each parameter the certificate should name what was measured, the method behind the number, and the limit the lot had to meet. For a mineral salt the identity block comes first, because complete physical results for the wrong salt are still the wrong salt.
| Test | Method | Limit at release |
|---|---|---|
| Appearance | Visual | White to yellowish, fine powder |
| Identification, iron | Wet reaction | Conforms |
| Identification, pyrophosphate | Wet reaction after hydrolysis | Conforms |
| Iron (Fe) | ICP-OES | 24.0–26.0% |
| Loss on drying | Gravimetric | ≤5.0% |
| Particle size | Sieve analysis, 200 mesh | ≥95% through |
The two identification lines are not interchangeable. The iron reaction answers for ferrous fumarate, ferrous sulfate and iron oxide as readily as for this salt; only the pyrophosphate reaction narrows the answer. A certificate that prints "iron: conforms" and stops has tested half the material.
| Test | Method | Limit at release |
|---|---|---|
| Bulk density | Cylinder method | 0.40–0.80 g/mL |
| Lead | ICP-MS | ≤3 mg/kg |
| Arsenic | ICP-MS | ≤2 mg/kg |
| Cadmium | ICP-MS | ≤1 mg/kg |
| Mercury | ICP-MS | ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
What the iron percentage measures
Iron is reported as elemental iron. A result of 25.0% means 25 g of Fe in 100 g of powder, not 25% ferric pyrophosphate; the salt makes up most of the remaining mass with the water in the formula. ICP-OES measures the element in solution and cannot tell whether the iron arrived as Fe(II) or Fe(III). The valence needs another test.
The formula, Fe₄(P₂O₇)₃·xH₂O, sets what the iron figure can be. The anhydrous salt is about 30% iron by mass, and each molecule of water dilutes it. At roughly eight molecules of water the figure falls to about 25%, where the catalog window sits. A lot well above 26% describes another hydrate state or an added iron source; a lot well below 24% describes dilution or a different salt.
Loss on drying is a separate measurement. The water written into the formula is held in the crystal and is not necessarily removed under the conditions of the test, so a 3% LOD is not proof of an anhydrous powder. Read the LOD as surface moisture and handling history; read the iron result with the declared hydrate as the description of the salt.
The limit and the batch result
A limit is the gate; a batch result is what the laboratory found. They belong in separate columns, and a column that merely repeats the range has not reported anything. An iron result of 24.1% and one of 25.9% both pass, yet they ask for different powder weights per dose; a lot at 95.0% through 200 mesh and one at 99.5% behave differently in a blender even though both pass.
| Parameter | Limit | The result column should give |
|---|---|---|
| Iron | 24.0–26.0% | The lot's ICP-OES figure, with the method named |
| Loss on drying | ≤5.0% | The measured percentage, not "complies" |
| Particle size | ≥95% through 200 mesh | The percentage passing and the sieve method |
| Heavy metals | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg | Four separate results in mg/kg |
Some lines need a number rather than a range. A contaminant result needs a figure and a detection limit; a microbiology line needs the count and the absence statement. "Passes specification" is a conclusion, and it should be possible to draw it from the figures above it.
What moves between batches
Iron moves with hydration, because water dilutes the metal, and with the reaction yield. A stable process still shows a spread inside the window.
Milling is the largest source of physical variation. A sieve result of "95% through 200 mesh" is one cut, not a distribution: two lots can pass the same sieve and differ in the fines that make dust and the coarse tail that settles in a drink mix. Bulk density moves with the same step, which is why 0.40–0.80 g/mL is a wide window.
Colour is the qualitative line. White to yellowish covers a real range; a strong yellow or brown tint can follow a hot drying step, a trace of iron oxide or a different hydrate. Ask for the batch record before rejecting on tint, and watch a trend rather than one result at the edge.
When to order an outside test
An independent test is worth ordering when the source is new, when a first shipment enters a regulated market, when a form is claimed but not evidenced by the supplier's own data, or when two laboratories disagree. The useful panel is targeted: ICP-MS for the heavy metals, X-ray diffraction for the crystalline phase, ion chromatography or a phosphate method for the pyrophosphate, and a speciation test for the valence.
Ask the laboratory to report its detection limit beside every "not detected". A screen without a limit says something about the instrument, not about the drum. The iron report should name the technique, the sample preparation and the basis, not only the percentage.
Chain of custody decides whether the report is evidence. The material tested and the material kept on file should be the same sample, identified by lot code.
What to compare between suppliers
Line up six items: the species and hydrate declared; the iron result and its method; the pyrophosphate identity and the iron-to-phosphate ratio; loss on drying; particle size and bulk density; the contaminant and microbiology panel. Two certificates that agree on iron and diverge on the other five are describing different powders.
Traceability is the second layer. The lot code should be the same on certificate, pack label and retained sample, and the certificate should name the manufacturing site.
The catalog specification sits on the iron pyrophosphate product page. The grade page compares the physical lines; the identity page runs the tests that separate the ferric salt from a ferrous one; the release workflow is on the quality page. The method is explained in the ICP-OES note.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation