How we prove a calcium gluconate lot is the gluconate
The question is not whether the powder contains calcium; every calcium salt does. The question is whether the anion is gluconate and whether the crystal is the monohydrate. IR, a gluconate-specific assay, Karl Fischer and XRD answer those questions, while the calcium titration only establishes the quantity. A certificate that stops at the calcium figure has measured the element and left the identity open.
Identity needs the gluconate anion as well as the calcium: a calcium titration alone fits carbonate, citrate and lactate too.
Checks that answer different questions
No single measurement establishes a salt. The document names what was ordered, the spectrum looks at the functional groups, the titration measures calcium, and the anion assay measures the part that makes the material gluconate. Water and diffraction then place the crystal. Each check can pass while another fails, which is why they are read together.
| Check | What it answers | Method | What it establishes |
|---|---|---|---|
| Document | Is the hydrate and CAS named? | Name, CAS number, formula | Only what was ordered |
| Spectrum | Do the functional groups match? | IR against a reference | The salt family, not the assay |
| Calcium | Is the calcium figure consistent? | Complexometric titration | Quantity of calcium |
| Anion | Is gluconate present? | Ion chromatography or an equivalent assay | The gluconate itself |
| Crystal | Is it the monohydrate? | XRD and Karl Fischer water | The hydrate state |
The calcium-to-gluconate balance
One calcium ion belongs to one gluconate unit, so the mass ratio is fixed: 40.078 ÷ 448.39 = 1 : 11.19 for the monohydrate, or 1 : 10.74 for the anhydrous salt. The theoretical calcium figures follow: 8.94% for the monohydrate and 9.31% for the anhydrous form. The catalogue range of 8.5–9.5% brackets both, which is why calcium alone cannot fix the hydrate.
The ratio is still a useful screen. A 8.94% calcium result should sit with an assay near 100% calcium gluconate monohydrate; a 8.5% result should sit near 95.1%. If the calcium is in range but the gluconate assay is far below the ratio, the powder is a blend. Calcium carbonate, calcium lactate and calcium citrate can all be blended to hit a calcium figure, but none of them supplies the gluconate.
Water completes the balance. At 4.0% water and a 100% dried-basis assay, 100 g of powder holds 96.0 g of dry matter and 8.94 g of calcium. At 6.0% water the as-is calcium falls to about 8.75% while the dried-basis assay remains in range. Reading calcium without water can make a correct lot look low, or a diluted lot look normal.
Diffraction and the solid state
Diffraction addresses the crystal rather than the solution. The monohydrate and the anhydrous salt pack into different lattices and give different patterns, so a diffractogram can show which hydrate is in the drum. A crystalline foreign phase, such as calcite in a carbonate blend or a lactate pattern in a mixed salt, may also appear.
XRD is not a purity assay, and it does not measure calcium. It is a solid-state check that earns its place when the hydrate is disputed or a new source is being qualified. Ask for the reference pattern and the detection limit before accepting a “match” statement. A report that says only “XRD conforms” has not shown the reader the evidence.
Heavily milled or amorphous material can give a broad pattern that is hard to compare. In that case IR, the anion assay and the water figure carry more weight. The methods are complementary; none of them is a substitute for the others.
Blends and substitutions
| Material | Why it is used | Signal | Test |
|---|---|---|---|
| Calcium carbonate | Cheap calcium; high density | Calcium high; gluconate low; calcite pattern | Anion assay, XRD, FTIR |
| Calcium lactate | Similar white powder | Calcium near 13%; gluconate low | Anion assay, IR, XRD |
| Calcium citrate | Higher calcium; different solubility | Calcium near 21%; gluconate low | Anion assay, IR |
| Maltodextrin or sugar | Bulking and dilution | Calcium and assay low; water normal | Mass balance, anion assay |
| Excess water | Lowers the as-is figures | Water above 6.0% | Karl Fischer |
| Sulfate or chloride | Neutralisation residue | Conductivity or ash; ion response | Ion chromatography |
Colour proves little. White to off-white covers many powders, and a blend can match it. The reliable signals are the anion assay, the calcium-to-gluconate ratio, the water figure and the crystal pattern.
Identity clauses for the specification
- “Calcium gluconate monohydrate, CAS 18016-24-5, C12H22CaO14·H2O.”
- “Assay 98.0–102.0% as calcium gluconate by complexometric titration; state the basis.”
- “Calcium 8.5–9.5%; water 3.0–6.0% by Karl Fischer.”
- “IR spectrum to match the reference; attach the spectrum or the band list.”
- “Gluconate-specific assay by ion chromatography or an equivalent method where the anion is to be confirmed.”
- “XRD reference pattern for the monohydrate where the hydrate state is in question.”
- “Particle size ≥95% through 40 mesh; heavy metals and microbiology as listed.”
Questions to put to the supplier
- Which hydrate is this lot, and which CAS number appears on the certificate?
- Will you send the IR spectrum and a gluconate-specific assay, not only the calcium result?
- What are the calcium and water figures, and how was the assay basis calculated?
- Has the lot been examined by XRD, and can the pattern and reference be shared?
- If the result is disputed, will you join a re-test on the retained sample?
Answers to those five questions make an identity file. A calcium percentage on its own does not. The product hub carries the catalogue specification; the COA page shows where each figure sits on the certificate; the grades page compares the hydrates; the XRD method note explains the solid-state check; the quality page describes the release workflow.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation