What the calcium carbonate COA reports, line by line
A calcium carbonate certificate reports appearance, identification, the assay by complexometric titration, elemental calcium, loss on drying, acid-insoluble matter, heavy metals, microbiology and particle size. Each line should carry its method and release limit, with the measured result in a separate column. The assay and the calcium figure are not the same measurement, and the certificate is only auditable when both are stated with their basis.
The assay and the calcium figure answer different questions, and the certificate is only auditable when both carry their method, their limit and the result for the lot.
The certificate as a test report
A certificate is a test report, not a label. Each parameter needs the measurement, the method and the limit the lot was released against. A row that says only “conforms” asks the reader to trust a conclusion without the evidence behind it. Appearance is descriptive; identification, assay and acid-insoluble matter are the lines that describe the material.
The certificate should name its identification tests; the catalog requires infrared and titration. The assay is a complexometric titration of calcium with EDTA, and the calculation then expresses the result as CaCO₃. Acid-insoluble matter is a gravimetric residue left after acid digestion, and it is the line that shows mineral grit rather than carbonate.
| Parameter | Method | Release limit |
|---|---|---|
| Identification | Infrared and complexometric titration | Conforms to the reference |
| Assay | Complexometric titration, calculated as CaCO₃ | ≥99.0% |
| Calcium | Complexometric titration | 39.0–41.0% |
| Loss on drying | Gravimetric, oven | ≤1.0% |
| Acid-insoluble matter | Gravimetric after acid digestion | ≤0.2% |
| Heavy metals | ICP-MS | Pb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg |
| Microbiology | Plate count and absence tests | APC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent |
| Particle size | Sieve analysis | ≥95% through 40 mesh |
Acid-insoluble matter is small in a precipitated grade and larger in a ground grade, because the residue carries the mineral fraction of the deposit. Particle size is a finishing specification, so it can move with the mill without any change in the chemistry.
The assay basis and the calcium arithmetic
Calcium carbonate has no water of crystallisation. Loss on drying measures surface moisture, and the oven test does not decompose the carbonate; calcination needs a kiln. That makes the basis simpler than for a hydrate, but the certificate should still state whether the assay is calculated on the dried basis or as received, and the calcium line should use the same basis.
The arithmetic links the two calcium lines. Calcium is 40.04% of CaCO₃ by mass, so an assay of 99.0% corresponds to 39.64% calcium. The catalog calcium window of 39.0–41.0% spans about 97.4–102.4% CaCO₃, which is wider at the bottom than the ≥99.0% assay gate. A lot at 39.3% calcium passes the calcium window and fails the assay. The assay is the release gate.
The titration measures calcium, not carbonate. A partially calcined lot, or a blend with calcium oxide or hydroxide, titrates as calcium and can report a high calcium figure while its carbonate content is lower. The acid reaction and the acid-insoluble line are the supporting evidence; carbon dioxide by acid gravimetry is the direct check, and the identity page sets out how the figures combine.
Release limit versus batch result
The release limit is the acceptance boundary for the lot. The batch result is what the laboratory measured on that lot. Both belong on the page, with the method beside them. A result column filled with the specification range is not a result; it is a copy of the gate.
| Parameter | Release limit | Result column |
|---|---|---|
| Assay | ≥99.0% as CaCO₃ | A measured percentage, with the method and the basis |
| Calcium | 39.0–41.0% | A measured percentage of the element |
| Loss on drying | ≤1.0% | A measured percentage |
| Acid-insoluble matter | ≤0.2% | A measured percentage and the acid used |
| Lead | ≤3 mg/kg | A measured figure with the limit of quantification |
| Particle size | ≥95% through 40 mesh | The measured percentage through the sieve |
“Passes specification” is a conclusion; the reader should be able to reach it from the numbers. Heavy metals need a figure per element, not a total, because a sum hides the element that matters. Lead is the first to read, and its margin against the limit is more informative than a bare pass.
What moves between batches
Precipitation conditions, the lime source and the carbonation endpoint move the particle size and the crystal form. A change from calcite to aragonite can change the bulk density and the acid reaction rate without moving the assay. Milling moves the particle distribution and the acid-insoluble residue; drying and packing move the moisture. None of those changes is visible in a single assay figure.
Whiteness is the least quantitative line. A precipitated and a ground grade can both be white, and a shell grade can carry a faint tone from residual organic matter. A colour shift is a reason to ask about the source, not a release failure by itself.
Lead is the line to trend. A lot at 0.3 mg/kg and the next at 2.4 mg/kg are both inside a 3 mg/kg limit, and the pair says something neither result says alone. For a shell grade, ask for lead with its limit of quantification on every lot.
When to order an outside test
Order an independent test for a new source, a first shipment into a regulated market, a shell grade, a disputed crystal form or a source claim on the label. The panel is calcium by EDTA with the pH and indicator, carbon dioxide by acid gravimetry, acid-insoluble matter, lead and the heavy-metal panel by ICP-MS, loss on drying, microbiology and particle size. Add X-ray diffraction when the crystal form or the source is in question.
Ask the laboratory what it can see. A lead result of “not detected” without a limit of quantification is a statement about the method, not about the lot. A carbon dioxide figure without the sample mass and the moisture correction is hard to audit. The report should identify the lot, and the sample tested should be the sample retained.
Source claims need documents rather than a test. X-ray diffraction can show a calcite or an aragonite pattern; it cannot show that the carbonate came from an oyster. The shell record, the supplier declaration and the chain of custody answer that question.
What to compare between suppliers
Put six lines side by side: source and crystal form; assay and calcium; loss on drying; acid-insoluble matter; lead with its limit of quantification; particle size and bulk density. Two quotations that agree on assay but differ on source or acid-insoluble matter are not describing the same powder.
Bulk density and flow are not on the catalog specification, so ask for them when the powder is going into a capsule or a tablet. The calcium carbonate product page carries the catalog figures. The grade comparison covers the source choice, the source comparison takes the lead and label questions further, the compliance page covers the market file, the methods index describes the tests, and the quality page describes the release workflow.
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation