06 Identity & adulteration

How to prove a lot is calcium carbonate

Technical document 06 · Reviewed 2026-11-19 · Calcium Carbonate

On this page
  1. The four identity layers
  2. The calcium-to-carbon dioxide ratio
  3. X-ray diffraction and the crystal form
  4. What substitution looks like
  5. How to write identity into the specification
  6. Five questions for the supplier

A calcium carbonate lot is proved by four agreeing measurements: the document names the source and the formula, the EDTA titration gives about 40% calcium and ≥99.0% CaCO₃, the acid reaction releases carbon dioxide in the proportion the formula predicts, and X-ray diffraction shows a carbonate crystal form rather than an oxide or a sulfate. The calcium figure alone cannot separate carbonate from oxide, hydroxide or a blend. The carbon dioxide and the acid-insoluble matter are what close the gap.

In one line

Calcium proves the element; the carbon dioxide released by acid and the crystal form shown by X-ray diffraction are what prove the powder is carbonate.

The four identity layers

A certificate can name the right material and still fail to prove it. The layers below are separate questions, and each one needs its own evidence. A supplier who answers only the first has described the paperwork, not the powder.

Four layers of calcium carbonate identity
LayerQuestionTestWhat it proves
DocumentIs the source and the formula named?Name, CAS number, source declarationPaperwork only
TitrationIs the calcium figure right?Complexometric titration with EDTAThe element, not the salt
Acid reactionIs the anion carbonate?Carbon dioxide by acid gravimetryThe carbonate anion
Solid stateWhich crystal form is present?X-ray diffractionCalcite, aragonite or vaterite

Acid-insoluble matter belongs beside these as a negative check: it measures what the acid did not dissolve, and a high residue points to silicate grit, a different mineral or a dirty source. It is not an identity test, but it limits how much of the powder can be something else.

The calcium-to-carbon dioxide ratio

Pure calcium carbonate is 40.04% calcium and 43.97% carbon dioxide by mass, a molar ratio of one calcium to one carbonate. The titration measures the calcium; acid gravimetry measures the carbon dioxide released when the powder dissolves. If both figures land on the formula, the mass balance is consistent with CaCO₃. If the calcium is high and the carbon dioxide is low, part of the calcium is present as oxide or hydroxide. If the carbon dioxide is high relative to the calcium, a magnesium carbonate or another carbonate salt is the likely explanation.

The arithmetic is simple enough to run on a certificate. One gram of pure carbonate releases about 0.44 g of carbon dioxide. A lot that reports 40.0% calcium and 36% carbon dioxide has a calcium-to-carbon dioxide mole ratio near 1.2, which is not calcium carbonate; the missing carbonate has to be explained before the lot is accepted. A certificate that reports only the calcium figure has left that check out.

The titration itself needs a method note. EDTA at pH 12–13 precipitates magnesium as the hydroxide and titrates calcium selectively; at pH 10 the same titrant measures calcium plus magnesium. A certificate that says “calcium by EDTA” without the pH and the indicator has not said which figure it reports. Ask for the method, especially when a magnesium carbonate is a plausible contaminant.

X-ray diffraction and the crystal form

Calcium carbonate crystallises as calcite, aragonite or vaterite. Calcite is the common form in mined limestone and in many precipitated grades; aragonite is denser and dissolves faster; vaterite is metastable and can convert to calcite in the presence of water. The three give different diffraction patterns, so X-ray diffraction can say which form is present and whether a second crystalline phase is visible.

The method answers a solid-state question, not a purity question. It can show that a lot is calcite rather than aragonite, or that an oxide or a sulfate phase is present above the detection limit. It cannot show that the carbonate came from an oyster, and it cannot quantify an amorphous fraction. Ask for the reference pattern, the scan range and the detection limit before reading a “match” statement.

Crystal form matters commercially when the powder is sold on a process claim or when the acid reaction rate is part of the specification. It also matters in a tablet: aragonite and calcite differ in density and in dissolution behaviour, so a form change can move the fill weight and the taste even when the assay does not move.

What substitution looks like

Substitutions and the signals that expose them
SubstituteWhat it doesSignalTest
Calcium oxide or hydroxideRaises calcium; no carbonate; alkalineHigh calcium, low carbon dioxide, fast acid reactionAcid gravimetry, pH, XRD
Calcium sulfateLowers calcium; no effervescenceNo carbon dioxide; sulfate presentAcid gravimetry, sulfate test, XRD
Calcium phosphateCalcium near the right figure; no carbonateNo carbon dioxide; phosphate presentAcid gravimetry, phosphate test
Magnesium carbonateAdds carbon dioxide; adds magnesiumCalcium low against carbon dioxide; magnesium detectedSelective EDTA, ICP-OES, XRD
Ground limestone in a precipitated lotMoves the residue and the particle distributionAcid-insoluble matter high; broad particle curveAcid-insoluble, particle size
Mined carbonate sold as shellNo chemical difference in the assaySource record does not match the claimTraceability documents, not XRD

Colour is the weakest signal. All three sources can be white, and a shell grade can carry a faint tone that a mined grade does not. The stronger signals are the carbon dioxide figure, the acid-insoluble residue, the crystal form and the lead result. A certificate that reports appearance, calcium and assay but not carbon dioxide has left the most likely substitution untested.

How to write identity into the specification

  • “Calcium carbonate, CAS 471-34-1, CaCO₃; source declared as precipitated, ground or oyster shell.”
  • “Assay ≥99.0% as CaCO₃ by complexometric titration; calcium 39.0–41.0%.”
  • “Identification by infrared and titration; carbon dioxide by acid gravimetry if agreed.”
  • “Loss on drying ≤1.0%; acid-insoluble matter ≤0.2%.”
  • “Crystal form by X-ray diffraction when calcite or aragonite is claimed.”
  • “No calcium oxide, calcium hydroxide, magnesium carbonate or other calcium salt added.”
  • “Source and crystal form under change control; lot code on the pack and the certificate.”

The negative clause is as important as the positive ones. A carbonate specification that does not exclude the oxide and the hydroxide leaves a partially calcined lot inside the calcium window, and the clause gives the laboratory a line to test against.

Five questions for the supplier

  1. Which source is this lot, and what does the source declaration say?
  2. What pH and indicator were used for the EDTA titration, and was magnesium masked?
  3. What is the carbon dioxide result, and how was it measured?
  4. Which crystal form does X-ray diffraction show, and what reference pattern was used?
  5. What is the lead result with its limit of quantification, and will you accept a joint re-test on the retained sample?

Five direct answers amount to an identity file; a calcium percentage does not. The product hub carries the catalog specification; the COA page shows where each figure sits on the certificate; the grade page compares the sources; the source comparison covers the lead and label consequences; the methods index explains the tests.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation