Cold-pressed or refined wheat germ oil: choosing a grade
Wheat germ oil is supplied cold-pressed or refined, and the two are different specifications. Cold pressing keeps the colour, the odour and a larger unsaponifiable fraction, and leaves a higher free fatty acid; refining lowers both the free fatty acid and the colour and removes part of the tocopherol and sterol fraction. The grade has to be named before the fatty-acid profile, the allergen statement and the dose form can be settled.
The grade decides how much colour, odour and unsaponifiable matter the oil carries, and the fatty-acid profile has to be re-stated for each grade.
Why wheat germ oil comes in two grades
The germ is a small part of the wheat kernel, and the oil is pressed or extracted from it. A mechanical press at low temperature is the cold-pressed route; the refined route adds degumming, neutralisation, bleaching and deodorisation, and sometimes winterisation to remove waxes. The two routes start from the same germ and end at different materials.
The difference is not cosmetic. Free fatty acid, colour, odour, the unsaponifiable fraction and the sediment all move, and the label may name the process. “Cold-pressed” is a process description, not a compositional guarantee: the profile still has to be measured on the lot.
The two grades side by side
| Dimension | Cold-pressed | Refined |
|---|---|---|
| Process | Mechanical press, low heat, no solvent | Degumming, neutralisation, bleaching, deodorisation |
| Free fatty acid | Higher; catalog limit ≤0.50% | Usually lower |
| Colour | Dark yellow to brownish | Lighter yellow |
| Odour and flavour | Strong, nutty, wheat-like | Mild, neutral |
| Tocopherols and sterols | Largely retained | Partly reduced |
| Peroxide value | Depends on press and storage; catalog ≤5.0 meq O₂/kg | Usually lower at release; can rise in storage |
| Sediment and haze | Waxes and cell debris can settle | Winterisation reduces haze |
| Wheat protein | Low but not zero; allergen assessment needed | Further reduced, but not assumed absent |
| Typical use | Softgel, oil blend, a label that names the process | Neutral blend, pale softgel, consistent flavour |
The table gives a direction, not a set of release values. Only the catalog limits — linoleic 50.0–60.0%, oleic 15.0–25.0%, palmitic 15.0–20.0%, FFA ≤0.50%, PV ≤5.0 meq O₂/kg, moisture ≤0.1% — are the gate for the cold-pressed grade. A refined grade needs its own specification, because the limits and the minor fraction are different.
Colour, haze and handling
Cold-pressed wheat germ oil is a dark, full-bodied oil with a strong cereal odour. It can be clear to slightly hazy, and a sediment of waxes may settle over time; the catalog allows the haze, so a hazy bottle is not automatically out of specification. Refined oil is lighter and cleaner-looking, and a customer who judges the oil by colour will read the two grades as different products even when the fatty-acid profile is close.
For a softgel, colour and odour are part of the consumer experience. A dark oil shows through a clear shell and flavours the fill; a refined oil keeps the capsule pale and the taste mild. For an oil blend, the cold-pressed odour can dominate a delicate formula, while the refined grade gives the formulator a neutral base. Neither grade is the right one in the abstract; the grade has to match the product.
The powder-on-carrier format is available on request. The carrier takes up part of the mass, so the linoleic figure on the powder is the oil's figure scaled by the oil load; the grade and the load both have to be declared. A powder made from cold-pressed oil carries the colour and odour of that oil, which can limit how much fits in a stick pack.
Dose arithmetic and the label
The dose form sets the mass, and the mass sets how much oil the label can claim. A 500 mg softgel of cold-pressed oil carries 250–300 mg of linoleic acid at the catalog range; a 1,000 mg softgel carries 500–600 mg. A refined oil with the same profile carries a similar fatty-acid mass, because refining does not concentrate linoleic, but the minor fraction is lower.
| Fill | At 50.0% linoleic | At 60.0% linoleic |
|---|---|---|
| 250 mg | 125 mg | 150 mg |
| 500 mg | 250 mg | 300 mg |
| 1,000 mg | 500 mg | 600 mg |
These are arithmetic, not an intake recommendation. If the label declares vitamin E from the oil, the tocopherol figure has to be measured and declared on the label's basis; it cannot be inferred from the grade name. If the label names the cold-pressed process, the process record and the grade belong in the specification.
What to write into the specification
- “Wheat germ oil (Triticum vulgare germ oil), CAS 8006-95-9, cold-pressed or refined — state which.”
- “Linoleic 50.0–60.0%, oleic 15.0–25.0%, palmitic 15.0–20.0% by GC-FID, on a stated basis.”
- “Free fatty acid ≤0.50% expressed as oleic acid; peroxide value ≤5.0 meq O₂/kg; moisture ≤0.1%.”
- “Appearance and colour range; sediment and haze allowed within the stated range.”
- “Unsaponifiable matter or tocopherol and sterol profile where the label uses them.”
- “Wheat allergen statement; a gluten statement only where a validated result supports it.”
- “Pack, storage condition and retest period.”
We supply the cold-pressed grade. A refined grade is a separate purchase, with its own FFA and colour limits; swapping one for the other needs a written change note and a fresh label review.
When the other grade is the wrong choice
Choose the refined grade when the product needs a light colour, a mild taste, a low free fatty acid at release, or a consistent flavour across lots. Choose the cold-pressed grade when the label names the process and the darker colour and fuller odour are part of the product. Choose neither when the formula cannot carry a wheat declaration; the allergen question is set out on the compliance page.
The grade is not a substitute for the profile. A refined oil can meet the appearance and FFA expectations and still sit outside the linoleic range; a cold-pressed oil can be dark and fresh or dark and oxidised. Read the grade, the profile, the oxidation values and the allergen statement together. The catalog specification is on the product page; the release lines are on the COA page; the oxidation behaviour is on the stability page; the pack and minimum are on the MOQ page; the tests are described in the methods index, and the release workflow is on the quality page. The carrier-borne grade comparison is on the flaxseed oil powder page.
In this document
Related documents
Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.
Request a quotation