01 COA & batch testing

What a sunflower lecithin COA has to show

Technical document 01 · Reviewed 2026-11-20 · Sunflower Lecithin

On this page
  1. The certificate as a release document
  2. Acetone-insoluble matter, phosphorus and the sunflower factor
  3. Release limit and batch result
  4. What changes from lot to lot
  5. When an outside test is worth ordering
  6. Comparing two sunflower certificates

A sunflower lecithin certificate describes a mixture, so it reports composition rather than one potency. Acetone-insoluble matter and the phosphorus-based phospholipid figure size the phosphatide fraction, the fatty acid and sterol lines name the plant source, and moisture, acid value and peroxide value record the condition of the lot. The catalog limits below are release gates; the batch COA is the evidence for a particular pack.

In one line

The phospholipid figure only means something with its basis and its source: acetone-insoluble matter, the phosphorus factor and the sunflower profile answer three different questions.

The certificate as a release document

A useful certificate can be audited line by line. Each row should say what was measured, which method produced the number, which limit the lot was released against, and what the lot actually measured. A row that reports only “conforms” asks the reader to accept a conclusion without the evidence behind it.

Read the sheet in four blocks: what the material is, how much phosphatide it carries, what condition it is in, and what has been screened out. The identity block is where the source is named; for sunflower lecithin that means the plant name and, where a claim depends on it, the seed type.

Release lines on a sunflower lecithin certificate
TestMethodRelease limit
AppearanceVisualYellow to light brown powder or viscous fluid
IdentificationPhospholipid profile by TLC or HPLCProfile conforms to the reference
Acetone-insoluble matterGravimetric, acetone extraction≥60.0%
PhospholipidsPhosphorus method, factor stated≥60.0%
MoistureKarl Fischer or loss on drying, as stated≤1.0%
Acid valueTitration, mg KOH/g≤30
Peroxide valueTitration, meq O₂/kgReported; not a catalog release gate
Heavy metalsICP-MSPb ≤3 · As ≤2 · Cd ≤1 · Hg ≤0.1 mg/kg
MicrobiologyPlate count and absence testsAPC ≤1,000 cfu/g; yeast and mould ≤100 cfu/g; E. coli and Salmonella absent

Peroxide value and residual solvent sit outside the catalog gates, but both belong in a buyer's file for a material that carries oil or was solvent-extracted.

Acetone-insoluble matter, phosphorus and the sunflower factor

Acetone is the solvent that separates phosphatides from oil. Triglycerides, free fatty acids and sterols dissolve; the phosphatides stay behind as a residue. Drying and weighing that residue gives acetone-insoluble matter. It is a residue weight, not a class-specific assay, and non-phospholipid material that resists acetone is counted with it.

The phospholipid figure is usually a calculation: phosphorus is measured, then multiplied by a factor derived from the average molecular weight of the phosphatides. The certificate should print the factor. Sunflower gums and soy gums do not have the same class pattern, so a factor copied from a soy specification is not automatically the right one for a sunflower lot. A lot measured at 2.45% phosphorus reads 61.3% at a factor of 25 and 64.4% at 26.3; the sheet should say which convention was used.

Moisture has its own convention. Karl Fischer titrates water; drying at 105 °C also drives off other volatiles. The catalog limit is moisture at ≤1.0%, while the EU additive entry limits loss on drying at ≤2.0%, so a lot can meet one number and miss the other unless the method is printed beside the result.

Release limit and batch result

A release limit is the boundary; a result is a measurement. Both belong on the page, in separate columns, with the method next to them. A result column that repeats the catalog range is a copy of the gate, not evidence from the lot.

What the result column should contain
ParameterRelease limitResult column
Acetone-insoluble matter≥60.0%A measured percentage and the drying condition
Phospholipids≥60.0%A measured percentage, the phosphorus figure and the factor
Moisture≤1.0%A measured percentage and the method
Acid value≤30 mg KOH/gA measured figure
Heavy metalsPer elementA figure in mg/kg for each element
MicrobiologyCounts and absenceThe count and the absence statement for the lot

Judge the lot from the numbers. A single heavy-metal total hides the element that drove it, and “pass” without a count and an absence statement is not a microbiology result. For the sunflower source, add the fatty acid or sterol result when the order depends on the source claim.

What changes from lot to lot

Four things move between sunflower lecithin lots: the oil left in the product, the seed type, the phospholipid class pattern, and the moisture and acid value. Oil and seed type are set at the seed and at degumming; the class pattern follows the seed and the gum process; moisture and acid value are shaped by drying and by storage. Colour follows all four and is the least diagnostic of them.

Seed type is easy to overlook. Standard sunflower is linoleic-rich; a high-oleic sunflower shifts the fatty acid profile toward oleic acid and changes the oxidation behaviour of the oil fraction. If the certificate or the order refers to a seed type, the fatty acid profile should support it.

Watch the direction across shipments rather than one result. An acid value that has climbed toward 30, moisture sitting at 0.9%, or an acetone-insoluble figure that has fallen toward 60 says more than a single pass. The lot code on the certificate should match the pouch, the drum and the retained sample.

When an outside test is worth ordering

Order an independent test for a new source, a first shipment into a regulated market, a soy-free claim that rests only on the name, or a disputed oxidation result. A useful outside panel adds a check that the release certificate does not make.

Start with the doubt. If the source is in doubt, the useful tests are acetone-insoluble matter, phosphorus, the phospholipid class profile, and the fatty acid and sterol profiles. If the condition is in doubt, acid value, peroxide value and moisture answer it. If the allergen statement is in doubt, ask for the manufacturer's line record and, where the claim needs one, a soy-specific test with a stated detection limit.

If a result is disputed, the referee should receive the retained sample together with the supplier's certificate and the written specification, and the request should name the test that separates one source from another. A repeat of the same assay rarely settles the question.

Comparing two sunflower certificates

Compare certificates on six lines: source and seed type, acetone-insoluble matter, the phospholipid figure with its factor, the class and fatty acid profiles, acid and peroxide values, and the contaminant panel. Two suppliers can both quote “60% sunflower lecithin” and still be selling different materials if one figure is AI and the other is a phosphorus calculation.

Ask who manufactured the lot, which country grew the seed, how the gum was separated and dried, and whether the line is shared with soy. Those answers decide whether the allergen statement is supportable. The catalog specification sits on the sunflower lecithin product page; the source tests are on the identity page; the market file is on the compliance page; the assays are described in the methods library; release is described on the quality page.

Send the specification you intend to use — grade, quantity and destination market — and we will reply with the batch COA, the technical data sheet and a quotation.

Request a quotation